Subversion Repositories shark

Rev

Details | Last modification | View Log | RSS feed

Rev Author Line No. Line
420 giacomo 1 
/* ------------------------------------------------------------------------- */
2 
/* i2c-iop3xx.h algorithm driver definitions private to i2c-iop3xx.c         */
3 
/* ------------------------------------------------------------------------- */
4 
/*   Copyright (C) 2003 Peter Milne, D-TACQ Solutions Ltd
5 
 *                      <Peter dot Milne at D hyphen TACQ dot com>
6 
 
7 
    This program is free software; you can redistribute it and/or modify
8 
    it under the terms of the GNU General Public License as published by
9 
    the Free Software Foundation, version 2.
10 
 
11 
    This program is distributed in the hope that it will be useful,
12 
    but WITHOUT ANY WARRANTY; without even the implied warranty of
13 
    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
14 
    GNU General Public License for more details.
15 
 
16 
    You should have received a copy of the GNU General Public License
17 
    along with this program; if not, write to the Free Software
18 
    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.                */
19 
/* ------------------------------------------------------------------------- */
20 
 
21 
 
22 
#ifndef I2C_IOP3XX_H
23 
#define I2C_IOP3XX_H 1
24 
 
25 
/*
26 
 * iop321 hardware bit definitions
27 
 */
28 
#define IOP321_ICR_FAST_MODE    0x8000  /* 1=400kBps, 0=100kBps */
29 
#define IOP321_ICR_UNIT_RESET   0x4000  /* 1=RESET */
30 
#define IOP321_ICR_SADIE        0x2000  /* 1=Slave Detect Interrupt Enable */
31 
#define IOP321_ICR_ALDIE        0x1000  /* 1=Arb Loss Detect Interrupt Enable */
32 
#define IOP321_ICR_SSDIE        0x0800  /* 1=Slave STOP Detect Interrupt Enable */
33 
#define IOP321_ICR_BERRIE       0x0400  /* 1=Bus Error Interrupt Enable */
34 
#define IOP321_ICR_RXFULLIE     0x0200  /* 1=Receive Full Interrupt Enable */
35 
#define IOP321_ICR_TXEMPTYIE    0x0100  /* 1=Transmit Empty Interrupt Enable */
36 
#define IOP321_ICR_GCD          0x0080  /* 1=General Call Disable */
37 
/*
38 
 * IOP321_ICR_GCD: 1 disables response as slave. "This bit must be set
39 
 * when sending a master mode general call message from the I2C unit"
40 
 */
41 
#define IOP321_ICR_UE           0x0040  /* 1=Unit Enable */
42 
/*
43 
 * "NOTE: To avoid I2C bus integrity problems,
44 
 * the user needs to ensure that the GPIO Output Data Register -
45 
 * GPOD bits associated with an I2C port are cleared prior to setting
46 
 * the enable bit for that I2C serial port.
47 
 * The user prepares to enable I2C port 0 and
48 
 * I2C port 1 by clearing GPOD bits 7:6 and GPOD bits 5:4, respectively.
49 
 */
50 
#define IOP321_ICR_SCLEN        0x0020  /* 1=SCL enable for master mode */
51 
#define IOP321_ICR_MABORT       0x0010  /* 1=Send a STOP with no data
52 
                                         * NB TBYTE must be clear */
53 
#define IOP321_ICR_TBYTE        0x0008  /* 1=Send/Receive a byte. i2c clears */
54 
#define IOP321_ICR_NACK         0x0004  /* 1=reply with NACK */
55 
#define IOP321_ICR_MSTOP        0x0002  /* 1=send a STOP after next data byte */
56 
#define IOP321_ICR_MSTART       0x0001  /* 1=initiate a START */
57 
 
58 
 
59 
#define IOP321_ISR_BERRD        0x0400  /* 1=BUS ERROR Detected */
60 
#define IOP321_ISR_SAD          0x0200  /* 1=Slave ADdress Detected */
61 
#define IOP321_ISR_GCAD         0x0100  /* 1=General Call Address Detected */
62 
#define IOP321_ISR_RXFULL       0x0080  /* 1=Receive Full */
63 
#define IOP321_ISR_TXEMPTY      0x0040  /* 1=Transmit Empty */
64 
#define IOP321_ISR_ALD          0x0020  /* 1=Arbitration Loss Detected */
65 
#define IOP321_ISR_SSD          0x0010  /* 1=Slave STOP Detected */
66 
#define IOP321_ISR_BBUSY        0x0008  /* 1=Bus BUSY */
67 
#define IOP321_ISR_UNITBUSY     0x0004  /* 1=Unit Busy */
68 
#define IOP321_ISR_NACK         0x0002  /* 1=Unit Rx or Tx a NACK */
69 
#define IOP321_ISR_RXREAD       0x0001  /* 1=READ 0=WRITE (R/W bit of slave addr */
70 
 
71 
#define IOP321_ISR_CLEARBITS    0x07f0
72 
 
73 
#define IOP321_ISAR_SAMASK      0x007f
74 
 
75 
#define IOP321_IDBR_MASK        0x00ff
76 
 
77 
#define IOP321_IBMR_SCL         0x0002
78 
#define IOP321_IBMR_SDA         0x0001
79 
 
80 
#define IOP321_GPOD_I2C0        0x00c0  /* clear these bits to enable ch0 */
81 
#define IOP321_GPOD_I2C1        0x0030  /* clear these bits to enable ch1 */
82 
 
83 
#define MYSAR                   0x02    /* SWAG a suitable slave address */
84 
 
85 
#define I2C_ERR                 321
86 
#define I2C_ERR_BERR            (I2C_ERR+0)
87 
#define I2C_ERR_ALD             (I2C_ERR+1)
88 
 
89 
 
90 
struct iop3xx_biu {                /* Bus Interface Unit - the hardware */
91 
/* physical hardware defs - regs*/
92 
        u32 *CR;
93 
        u32 *SR;
94 
        u32 *SAR;
95 
        u32 *DBR;
96 
        u32 *BMR;
97 
/* irq bit vector */
98 
        u32 irq;
99 
/* stored flags */
100 
        u32 SR_enabled, SR_received;
101 
};
102 
 
103 
struct i2c_algo_iop3xx_data {
104 
        int channel;
105 
 
106 
        wait_queue_head_t waitq;
107 
        spinlock_t lock;
108 
        int timeout;
109 
        struct iop3xx_biu* biu;
110 
};
111 
 
112 
#define REGION_START(adap)      ((u32)((adap)->biu->CR))
113 
#define REGION_END(adap)        ((u32)((adap)->biu->BMR+1))
114 
#define REGION_LENGTH(adap)     (REGION_END(adap)-REGION_START(adap))
115 
 
116 
#define IRQ_STATUS_MASK(adap)   (1<<adap->biu->irq)
117 
 
118 
#endif /* I2C_IOP3XX_H */