Subversion Repositories shark

/* header file for DIO boards for the HP300 architecture.

 * Maybe this should handle DIO-II later?

 * The general structure of this is vaguely based on how

 * the Amiga port handles Zorro boards.

 * Copyright (C) Peter Maydell 05/1998 <pmaydell@chiark.greenend.org.uk>

 *

 * The board IDs are from the NetBSD kernel, which for once provided

 * helpful comments...

 *

 * This goes with arch/m68k/hp300/dio.c

 */

#ifndef _LINUX_DIO_H

#define _LINUX_DIO_H

/* The DIO boards in a system are distinguished by 'select codes' which

 * range from 0-63 (DIO) and 132-255 (DIO-II).

 * The DIO board with select code sc is located at physical address

 *     0x600000 + sc * 0x10000

 * So DIO cards cover [0x600000-0x800000); the areas [0x200000-0x400000) and

 * [0x800000-0x1000000) are for additional space required by things

 * like framebuffers. [0x400000-0x600000) is for miscellaneous internal I/O.

 * On Linux, this is currently all mapped into the virtual address space

 * at 0xf0000000 on bootup.

 * DIO-II boards are at 0x1000000 + (sc - 132) * 0x400000

 * which is address range [0x1000000-0x20000000) -- too big to map completely,

 * so currently we just don't handle DIO-II boards.  It wouldn't be hard to

 * do with ioremap() though.

 */

#ifdef __KERNEL__

/* DIO/DIO-II boards all have the following 8bit registers.

 * These are offsets from the base of the device.

 */

#define DIO_IDOFF     0x01                        /* primary device ID */

#define DIO_IPLOFF    0x03                        /* interrupt priority level */

#define DIO_SECIDOFF  0x15                        /* secondary device ID */

#define DIOII_SIZEOFF 0x101                       /* device size, DIO-II only */

/* The internal HPIB device is special; this is its physaddr; its select code is 7.

 * The reason why we have to treat it specially is because apparently it's broken:

 * the device ID isn't consistent/reliable. *sigh*

 */

#define DIO_IHPIBADDR 0x47800

#define DIO_IHPIBSCODE 7

/* If we don't have the internal HPIB defined, then treat select code 7 like

 * any other. If we *do* have internal HPIB, then we just have to assume that

 * select code 7 is the internal HPIB regardless of the ID register :-<

 */

#define CONFIG_IHPIB /* hack hack : not yet a proper config option */

#ifdef CONFIG_IHPIB

#define DIO_ISIHPIB(scode) ((scode) == DIO_IHPIBSCODE)

#else

#define DIO_ISIHPIB(scode) 0

#endif

#define DIO_VIRADDRBASE 0xf0000000                /* vir addr where IOspace is mapped */

#define DIO_BASE                0x600000        /* start of DIO space */

#define DIO_END                 0x1000000       /* end of DIO space */

#define DIO_DEVSIZE             0x10000         /* size of a DIO device */

#define DIOII_BASE              0x01000000      /* start of DIO-II space */

#define DIOII_END               0x20000000      /* end of DIO-II space */

#define DIOII_DEVSIZE           0x00400000      /* size of a DIO-II device */

/* Highest valid select code. If we add DIO-II support this should become

 * 256 for everything except HP320, which only has DIO.

 */

#define DIO_SCMAX 32                             

#define DIOII_SCBASE 132 /* lowest DIO-II select code */

#define DIO_SCINHOLE(scode) (((scode) >= 32) && ((scode) < DIOII_SCBASE))

/* macros to read device IDs, given base address */

#define DIO_ID(baseaddr) in_8((baseaddr) + DIO_IDOFF)

#define DIO_SECID(baseaddr) in_8((baseaddr) + DIO_SECIDOFF)

/* extract the interrupt level */

#define DIO_IPL(baseaddr) (((in_8((baseaddr) + DIO_IPLOFF) >> 4) & 0x03) + 3)

/* find the size of a DIO-II board's address space.

 * DIO boards are all fixed length.

 */

#define DIOII_SIZE(baseaddr) ((in_8((baseaddr) + DIOII_SIZEOFF) + 1) * 0x100000)

/* general purpose macro for both DIO and DIO-II */

#define DIO_SIZE(scode, base) (DIO_ISDIOII((scode)) ? DIOII_SIZE((base)) : DIO_DEVSIZE)

/* The hardware has primary and secondary IDs; we encode these in a single

 * int as PRIMARY ID & (SECONDARY ID << 8).

 * In practice this is only important for framebuffers,

 * and everybody else just sets ID fields equal to the DIO_ID_FOO value.

 */

#define DIO_ENCODE_ID(pr,sec) ((((int)sec & 0xff) << 8) & ((int)pr & 0xff))

/* macro to determine whether a given primary ID requires a secondary ID byte */

#define DIO_NEEDSSECID(id) ((id) == DIO_ID_FBUFFER)

/* Now a whole slew of macros giving device IDs and descriptive strings: */

#define DIO_ID_DCA0     0x02 /* 98644A serial */

#define DIO_DESC_DCA0 "98644A DCA0 serial"

#define DIO_ID_DCA0REM  0x82 /* 98644A serial */

#define DIO_DESC_DCA0REM "98644A DCA0REM serial"

#define DIO_ID_DCA1     0x42 /* 98644A serial */

#define DIO_DESC_DCA1 "98644A DCA1 serial"

#define DIO_ID_DCA1REM  0xc2 /* 98644A serial */

#define DIO_DESC_DCA1REM "98644A DCA1REM serial"

#define DIO_ID_DCM      0x05 /* 98642A serial MUX */

#define DIO_DESC_DCM "98642A DCM serial MUX"

#define DIO_ID_DCMREM   0x85 /* 98642A serial MUX */

#define DIO_DESC_DCMREM "98642A DCMREM serial MUX"

#define DIO_ID_LAN      0x15 /* 98643A LAN */

#define DIO_DESC_LAN "98643A LANCE ethernet"

#define DIO_ID_FHPIB    0x08 /* 98625A/98625B fast HP-IB */

#define DIO_DESC_FHPIB "98625A/98625B fast HPIB"

#define DIO_ID_NHPIB    0x80 /* 98624A HP-IB (normal ie slow) */

#define DIO_DESC_NHPIB "98624A HPIB"

#define DIO_ID_IHPIB    0x00 /* internal HPIB (not its real ID, it hasn't got one! */

#define DIO_DESC_IHPIB "internal HPIB"

#define DIO_ID_SCSI0    0x07 /* 98625A SCSI */

#define DIO_DESC_SCSI0 "98625A SCSI0"

#define DIO_ID_SCSI1    0x27 /* ditto */

#define DIO_DESC_SCSI1 "98625A SCSI1"

#define DIO_ID_SCSI2    0x47 /* ditto */

#define DIO_DESC_SCSI2 "98625A SCSI2"

#define DIO_ID_SCSI3    0x67 /* ditto */

#define DIO_DESC_SCSI3 "98625A SCSI3"

#define DIO_ID_FBUFFER  0x39 /* framebuffer: flavour is distinguished by secondary ID */

#define DIO_DESC_FBUFFER "bitmapped display"

/* the NetBSD kernel source is a bit unsure as to what these next IDs actually do :-> */

#define DIO_ID_MISC0    0x03 /* 98622A */

#define DIO_DESC_MISC0 "98622A"

#define DIO_ID_MISC1    0x04 /* 98623A */

#define DIO_DESC_MISC1 "98623A"

#define DIO_ID_PARALLEL 0x06 /* internal parallel */

#define DIO_DESC_PARALLEL "internal parallel"

#define DIO_ID_MISC2    0x09 /* 98287A keyboard */

#define DIO_DESC_MISC2 "98287A keyboard"

#define DIO_ID_MISC3    0x0a /* HP98635A FP accelerator */

#define DIO_DESC_MISC3 "HP98635A FP accelerator"

#define DIO_ID_MISC4    0x0b /* timer */

#define DIO_DESC_MISC4 "timer"

#define DIO_ID_MISC5    0x12 /* 98640A */

#define DIO_DESC_MISC5 "98640A"

#define DIO_ID_MISC6    0x16 /* 98659A */

#define DIO_DESC_MISC6 "98659A"

#define DIO_ID_MISC7    0x19 /* 237 display */

#define DIO_DESC_MISC7 "237 display"

#define DIO_ID_MISC8    0x1a /* quad-wide card */

#define DIO_DESC_MISC8 "quad-wide card"

#define DIO_ID_MISC9    0x1b /* 98253A */

#define DIO_DESC_MISC9 "98253A"

#define DIO_ID_MISC10   0x1c /* 98627A */

#define DIO_DESC_MISC10 "98253A"

#define DIO_ID_MISC11   0x1d /* 98633A */

#define DIO_DESC_MISC11 "98633A"

#define DIO_ID_MISC12   0x1e /* 98259A */

#define DIO_DESC_MISC12 "98259A"

#define DIO_ID_MISC13   0x1f /* 8741 */

#define DIO_DESC_MISC13 "8741"

#define DIO_ID_VME      0x31 /* 98577A VME adapter */

#define DIO_DESC_VME "98577A VME adapter"

#define DIO_ID_DCL      0x34 /* 98628A serial */

#define DIO_DESC_DCL "98628A DCL serial"

#define DIO_ID_DCLREM   0xb4 /* 98628A serial */

#define DIO_DESC_DCLREM "98628A DCLREM serial"

/* These are the secondary IDs for the framebuffers */

#define DIO_ID2_GATORBOX    0x01 /* 98700/98710 "gatorbox" */

#define DIO_DESC2_GATORBOX       "98700/98710 \"gatorbox\" display"

#define DIO_ID2_TOPCAT      0x02 /* 98544/98545/98547 "topcat" */

#define DIO_DESC2_TOPCAT         "98544/98545/98547 \"topcat\" display"

#define DIO_ID2_RENAISSANCE 0x04 /* 98720/98721 "renaissance" */

#define DIO_DESC2_RENAISSANCE    "98720/98721 \"renaissance\" display"

#define DIO_ID2_LRCATSEYE   0x05 /* lowres "catseye" */

#define DIO_DESC2_LRCATSEYE      "low-res catseye display"

#define DIO_ID2_HRCCATSEYE  0x06 /* highres colour "catseye" */

#define DIO_DESC2_HRCCATSEYE     "high-res color catseye display"

#define DIO_ID2_HRMCATSEYE  0x07 /* highres mono "catseye" */

#define DIO_DESC2_HRMCATSEYE     "high-res mono catseye display"

#define DIO_ID2_DAVINCI     0x08 /* 98730/98731 "davinci" */

#define DIO_DESC2_DAVINCI        "98730/98731 \"davinci\" display"

#define DIO_ID2_XXXCATSEYE  0x09 /* "catseye" */

#define DIO_DESC2_XXXCATSEYE     "catseye display"

#define DIO_ID2_HYPERION    0x0e /* A1096A "hyperion" */

#define DIO_DESC2_HYPERION       "A1096A \"hyperion\" display"

#define DIO_ID2_XGENESIS    0x0b /* "x-genesis"; no NetBSD support */

#define DIO_DESC2_XGENESIS       "\"x-genesis\" display"

#define DIO_ID2_TIGER       0x0c /* "tiger"; no NetBSD support */

#define DIO_DESC2_TIGER          "\"tiger\" display"

#define DIO_ID2_YGENESIS    0x0d /* "y-genesis"; no NetBSD support */

#define DIO_DESC2_YGENESIS       "\"y-genesis\" display"

/* if you add new IDs then you should tell dio.c about them so it can

 * identify them...

 */

extern int dio_find(int deviceid);

extern void *dio_scodetoviraddr(int scode);

extern int dio_scodetoipl(int scode);

extern const char *dio_scodetoname(int scode);

extern void dio_config_board(int scode);

extern void dio_unconfig_board(int scode);

#endif /* __KERNEL__ */

#endif /* ndef _LINUX_DIO_H */