Subversion Repositories shark

Rev

Details | Last modification | View Log | RSS feed

Rev Author Line No. Line
422 giacomo 1
#ifndef _LINUX_FDREG_H
2
#define _LINUX_FDREG_H
3
/*
4
 * This file contains some defines for the floppy disk controller.
5
 * Various sources. Mostly "IBM Microcomputers: A Programmers
6
 * Handbook", Sanches and Canton.
7
 */
8
 
9
#ifdef FDPATCHES
10
#define FD_IOPORT fdc_state[fdc].address
11
#else
12
/* It would be a lot saner just to force fdc_state[fdc].address to always
13
   be set ! FIXME */
14
#define FD_IOPORT 0x3f0
15
#endif
16
 
17
/* Fd controller regs. S&C, about page 340 */
18
#define FD_STATUS       (4 + FD_IOPORT )
19
#define FD_DATA         (5 + FD_IOPORT )
20
 
21
/* Digital Output Register */
22
#define FD_DOR          (2 + FD_IOPORT )
23
 
24
/* Digital Input Register (read) */
25
#define FD_DIR          (7 + FD_IOPORT )
26
 
27
/* Diskette Control Register (write)*/
28
#define FD_DCR          (7 + FD_IOPORT )
29
 
30
/* Bits of main status register */
31
#define STATUS_BUSYMASK 0x0F            /* drive busy mask */
32
#define STATUS_BUSY     0x10            /* FDC busy */
33
#define STATUS_DMA      0x20            /* 0- DMA mode */
34
#define STATUS_DIR      0x40            /* 0- cpu->fdc */
35
#define STATUS_READY    0x80            /* Data reg ready */
36
 
37
/* Bits of FD_ST0 */
38
#define ST0_DS          0x03            /* drive select mask */
39
#define ST0_HA          0x04            /* Head (Address) */
40
#define ST0_NR          0x08            /* Not Ready */
41
#define ST0_ECE         0x10            /* Equipment check error */
42
#define ST0_SE          0x20            /* Seek end */
43
#define ST0_INTR        0xC0            /* Interrupt code mask */
44
 
45
/* Bits of FD_ST1 */
46
#define ST1_MAM         0x01            /* Missing Address Mark */
47
#define ST1_WP          0x02            /* Write Protect */
48
#define ST1_ND          0x04            /* No Data - unreadable */
49
#define ST1_OR          0x10            /* OverRun */
50
#define ST1_CRC         0x20            /* CRC error in data or addr */
51
#define ST1_EOC         0x80            /* End Of Cylinder */
52
 
53
/* Bits of FD_ST2 */
54
#define ST2_MAM         0x01            /* Missing Address Mark (again) */
55
#define ST2_BC          0x02            /* Bad Cylinder */
56
#define ST2_SNS         0x04            /* Scan Not Satisfied */
57
#define ST2_SEH         0x08            /* Scan Equal Hit */
58
#define ST2_WC          0x10            /* Wrong Cylinder */
59
#define ST2_CRC         0x20            /* CRC error in data field */
60
#define ST2_CM          0x40            /* Control Mark = deleted */
61
 
62
/* Bits of FD_ST3 */
63
#define ST3_HA          0x04            /* Head (Address) */
64
#define ST3_DS          0x08            /* drive is double-sided */
65
#define ST3_TZ          0x10            /* Track Zero signal (1=track 0) */
66
#define ST3_RY          0x20            /* drive is ready */
67
#define ST3_WP          0x40            /* Write Protect */
68
#define ST3_FT          0x80            /* Drive Fault */
69
 
70
/* Values for FD_COMMAND */
71
#define FD_RECALIBRATE          0x07    /* move to track 0 */
72
#define FD_SEEK                 0x0F    /* seek track */
73
#define FD_READ                 0xE6    /* read with MT, MFM, SKip deleted */
74
#define FD_WRITE                0xC5    /* write with MT, MFM */
75
#define FD_SENSEI               0x08    /* Sense Interrupt Status */
76
#define FD_SPECIFY              0x03    /* specify HUT etc */
77
#define FD_FORMAT               0x4D    /* format one track */
78
#define FD_VERSION              0x10    /* get version code */
79
#define FD_CONFIGURE            0x13    /* configure FIFO operation */
80
#define FD_PERPENDICULAR        0x12    /* perpendicular r/w mode */
81
#define FD_GETSTATUS            0x04    /* read ST3 */
82
#define FD_DUMPREGS             0x0E    /* dump the contents of the fdc regs */
83
#define FD_READID               0xEA    /* prints the header of a sector */
84
#define FD_UNLOCK               0x14    /* Fifo config unlock */
85
#define FD_LOCK                 0x94    /* Fifo config lock */
86
#define FD_RSEEK_OUT            0x8f    /* seek out (i.e. to lower tracks) */
87
#define FD_RSEEK_IN             0xcf    /* seek in (i.e. to higher tracks) */
88
 
89
/* the following commands are new in the 82078. They are not used in the
90
 * floppy driver, except the first three. These commands may be useful for apps
91
 * which use the FDRAWCMD interface. For doc, get the 82078 spec sheets at
92
 * http://www-techdoc.intel.com/docs/periph/fd_contr/datasheets/ */
93
 
94
#define FD_PARTID               0x18    /* part id ("extended" version cmd) */
95
#define FD_SAVE                 0x2e    /* save fdc regs for later restore */
96
#define FD_DRIVESPEC            0x8e    /* drive specification: Access to the
97
                                         * 2 Mbps data transfer rate for tape
98
                                         * drives */
99
 
100
#define FD_RESTORE              0x4e    /* later restore */
101
#define FD_POWERDOWN            0x27    /* configure FDC's powersave features */
102
#define FD_FORMAT_N_WRITE       0xef    /* format and write in one go. */
103
#define FD_OPTION               0x33    /* ISO format (which is a clean way to
104
                                         * pack more sectors on a track) */
105
 
106
/* DMA commands */
107
#define DMA_READ        0x46
108
#define DMA_WRITE       0x4A
109
 
110
/* FDC version return types */
111
#define FDC_NONE        0x00
112
#define FDC_UNKNOWN     0x10    /* DO NOT USE THIS TYPE EXCEPT IF IDENTIFICATION
113
                                   FAILS EARLY */
114
#define FDC_8272A       0x20    /* Intel 8272a, NEC 765 */
115
#define FDC_765ED       0x30    /* Non-Intel 1MB-compatible FDC, can't detect */
116
#define FDC_82072       0x40    /* Intel 82072; 8272a + FIFO + DUMPREGS */
117
#define FDC_82072A      0x45    /* 82072A (on Sparcs) */
118
#define FDC_82077_ORIG  0x51    /* Original version of 82077AA, sans LOCK */
119
#define FDC_82077       0x52    /* 82077AA-1 */
120
#define FDC_82078_UNKN  0x5f    /* Unknown 82078 variant */
121
#define FDC_82078       0x60    /* 44pin 82078 or 64pin 82078SL */
122
#define FDC_82078_1     0x61    /* 82078-1 (2Mbps fdc) */
123
#define FDC_S82078B     0x62    /* S82078B (first seen on Adaptec AVA-2825 VLB
124
                                 * SCSI/EIDE/Floppy controller) */
125
#define FDC_87306       0x63    /* National Semiconductor PC 87306 */
126
 
127
/*
128
 * Beware: the fdc type list is roughly sorted by increasing features.
129
 * Presence of features is tested by comparing the FDC version id with the
130
 * "oldest" version that has the needed feature.
131
 * If during FDC detection, an obscure test fails late in the sequence, don't
132
 * assign FDC_UNKNOWN. Else the FDC will be treated as a dumb 8272a, or worse.
133
 * This is especially true if the tests are unneeded.
134
 */
135
 
136
#define FD_RESET_DELAY 20
137
#endif