Rev 846 |
Blame |
Compare with Previous |
Last modification |
View Log
| RSS feed
/*
* OHCI HCD (Host Controller Driver) for USB.
*
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
* (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
*
* This file is licenced under the GPL.
*/
/*
* OHCI Endpoint Descriptor (ED) ... holds TD queue
* See OHCI spec, section 4.2
*
* This is a "Queue Head" for those transfers, which is why
* both EHCI and UHCI call similar structures a "QH".
*/
struct ed {
/* first fields are hardware-specified, le32 */
__u32 hwINFO; /* endpoint config bitmap */
/* info bits defined by hcd */
#define ED_DEQUEUE __constant_cpu_to_le32(1 << 27)
/* info bits defined by the hardware */
#define ED_ISO __constant_cpu_to_le32(1 << 15)
#define ED_SKIP __constant_cpu_to_le32(1 << 14)
#define ED_LOWSPEED __constant_cpu_to_le32(1 << 13)
#define ED_OUT __constant_cpu_to_le32(0x01 << 11)
#define ED_IN __constant_cpu_to_le32(0x02 << 11)
__u32 hwTailP; /* tail of TD list */
__u32 hwHeadP; /* head of TD list (hc r/w) */
#define ED_C __constant_cpu_to_le32(0x02) /* toggle carry */
#define ED_H __constant_cpu_to_le32(0x01) /* halted */
__u32 hwNextED; /* next ED in list */
/* rest are purely for the driver's use */
dma_addr_t dma; /* addr of ED */
struct td *dummy; /* next TD to activate */
/* host's view of schedule */
struct ed *ed_next; /* on schedule or rm_list */
struct ed *ed_prev; /* for non-interrupt EDs */
struct list_head td_list; /* "shadow list" of our TDs */
/* create --> IDLE --> OPER --> ... --> IDLE --> destroy
* usually: OPER --> UNLINK --> (IDLE | OPER) --> ...
* some special cases : OPER --> IDLE ...
*/
u8 state; /* ED_{IDLE,UNLINK,OPER} */
#define ED_IDLE 0x00 /* NOT linked to HC */
#define ED_UNLINK 0x01 /* being unlinked from hc */
#define ED_OPER 0x02 /* IS linked to hc */
u8 type; /* PIPE_{BULK,...} */
/* periodic scheduling params (for intr and iso) */
u8 branch;
u16 interval;
u16 load;
u16 last_iso; /* iso only */
/* HC may see EDs on rm_list until next frame (frame_no == tick) */
u16 tick;
} __attribute__ ((aligned(16)));
#define ED_MASK ((u32)~0x0f) /* strip hw status in low addr bits */
/*
* OHCI Transfer Descriptor (TD) ... one per transfer segment
* See OHCI spec, sections 4.3.1 (general = control/bulk/interrupt)
* and 4.3.2 (iso)
*/
struct td {
/* first fields are hardware-specified, le32 */
__u32 hwINFO; /* transfer info bitmask */
/* hwINFO bits for both general and iso tds: */
#define TD_CC 0xf0000000 /* condition code */
#define TD_CC_GET(td_p) ((td_p >>28) & 0x0f)
//#define TD_CC_SET(td_p, cc) (td_p) = ((td_p) & 0x0fffffff) | (((cc) & 0x0f) << 28)
#define TD_DI 0x00E00000 /* frames before interrupt */
#define TD_DI_SET(X) (((X) & 0x07)<< 21)
/* these two bits are available for definition/use by HCDs in both
* general and iso tds ... others are available for only one type
*/
#define TD_DONE 0x00020000 /* retired to donelist */
#define TD_ISO 0x00010000 /* copy of ED_ISO */
/* hwINFO bits for general tds: */
#define TD_EC 0x0C000000 /* error count */
#define TD_T 0x03000000 /* data toggle state */
#define TD_T_DATA0 0x02000000 /* DATA0 */
#define TD_T_DATA1 0x03000000 /* DATA1 */
#define TD_T_TOGGLE 0x00000000 /* uses ED_C */
#define TD_DP 0x00180000 /* direction/pid */
#define TD_DP_SETUP 0x00000000 /* SETUP pid */
#define TD_DP_IN 0x00100000 /* IN pid */
#define TD_DP_OUT 0x00080000 /* OUT pid */
/* 0x00180000 rsvd */
#define TD_R 0x00040000 /* round: short packets OK? */
/* (no hwINFO #defines yet for iso tds) */
__u32 hwCBP; /* Current Buffer Pointer (or 0) */
__u32 hwNextTD; /* Next TD Pointer */
__u32 hwBE; /* Memory Buffer End Pointer */
/* PSW is only for ISO */
#define MAXPSW 1 /* hardware allows 8 */
__u16 hwPSW [MAXPSW];
/* rest are purely for the driver's use */
__u8 index;
struct ed *ed;
struct td *td_hash; /* dma-->td hashtable */
struct td *next_dl_td;
struct urb *urb;
dma_addr_t td_dma; /* addr of this TD */
dma_addr_t data_dma; /* addr of data it points to */
struct list_head td_list; /* "shadow list", TDs on same ED */
} __attribute__ ((aligned(32))); /* c/b/i need 16; only iso needs 32 */
#define TD_MASK ((u32)~0x1f) /* strip hw status in low addr bits */
/*
* Hardware transfer status codes -- CC from td->hwINFO or td->hwPSW
*/
#define TD_CC_NOERROR 0x00
#define TD_CC_CRC 0x01
#define TD_CC_BITSTUFFING 0x02
#define TD_CC_DATATOGGLEM 0x03
#define TD_CC_STALL 0x04
#define TD_DEVNOTRESP 0x05
#define TD_PIDCHECKFAIL 0x06
#define TD_UNEXPECTEDPID 0x07
#define TD_DATAOVERRUN 0x08
#define TD_DATAUNDERRUN 0x09
/* 0x0A, 0x0B reserved for hardware */
#define TD_BUFFEROVERRUN 0x0C
#define TD_BUFFERUNDERRUN 0x0D
/* 0x0E, 0x0F reserved for HCD */
#define TD_NOTACCESSED 0x0F
/* map OHCI TD status codes (CC) to errno values */
static const int cc_to_error [16] = {
/* No Error */ 0,
/* CRC Error */ -EILSEQ,
/* Bit Stuff */ -EPROTO,
/* Data Togg */ -EILSEQ,
/* Stall */ -EPIPE,
/* DevNotResp */ -ETIMEDOUT,
/* PIDCheck */ -EPROTO,
/* UnExpPID */ -EPROTO,
/* DataOver */ -EOVERFLOW,
/* DataUnder */ -EREMOTEIO,
/* (for hw) */ -EIO,
/* (for hw) */ -EIO,
/* BufferOver */ -ECOMM,
/* BuffUnder */ -ENOSR,
/* (for HCD) */ -EALREADY,
/* (for HCD) */ -EALREADY
};
/*
* The HCCA (Host Controller Communications Area) is a 256 byte
* structure defined section 4.4.1 of the OHCI spec. The HC is
* told the base address of it. It must be 256-byte aligned.
*/
struct ohci_hcca {
#define NUM_INTS 32
__u32 int_table [NUM_INTS]; /* periodic schedule */
__u16 frame_no; /* current frame number */
__u16 pad1; /* set to 0 on each frame_no change */
__u32 done_head; /* info returned for an interrupt */
u8 reserved_for_hc [116];
u8 what [4]; /* spec only identifies 252 bytes :) */
} __attribute__ ((aligned(256)));
/*
* This is the structure of the OHCI controller's memory mapped I/O region.
* You must use readl() and writel() (in <asm/io.h>) to access these fields!!
* Layout is in section 7 (and appendix B) of the spec.
*/
struct ohci_regs {
/* control and status registers (section 7.1) */
__u32 revision;
__u32 control;
__u32 cmdstatus;
__u32 intrstatus;
__u32 intrenable;
__u32 intrdisable;
/* memory pointers (section 7.2) */
__u32 hcca;
__u32 ed_periodcurrent;
__u32 ed_controlhead;
__u32 ed_controlcurrent;
__u32 ed_bulkhead;
__u32 ed_bulkcurrent;
__u32 donehead;
/* frame counters (section 7.3) */
__u32 fminterval;
__u32 fmremaining;
__u32 fmnumber;
__u32 periodicstart;
__u32 lsthresh;
/* Root hub ports (section 7.4) */
struct ohci_roothub_regs {
__u32 a;
__u32 b;
__u32 status;
#define MAX_ROOT_PORTS 15 /* maximum OHCI root hub ports (RH_A_NDP) */
__u32 portstatus [MAX_ROOT_PORTS];
} roothub;
/* and optional "legacy support" registers (appendix B) at 0x0100 */
} __attribute__ ((aligned(32)));
/* OHCI CONTROL AND STATUS REGISTER MASKS */
/*
* HcControl (control) register masks
*/
#define OHCI_CTRL_CBSR (3 << 0) /* control/bulk service ratio */
#define OHCI_CTRL_PLE (1 << 2) /* periodic list enable */
#define OHCI_CTRL_IE (1 << 3) /* isochronous enable */
#define OHCI_CTRL_CLE (1 << 4) /* control list enable */
#define OHCI_CTRL_BLE (1 << 5) /* bulk list enable */
#define OHCI_CTRL_HCFS (3 << 6) /* host controller functional state */
#define OHCI_CTRL_IR (1 << 8) /* interrupt routing */
#define OHCI_CTRL_RWC (1 << 9) /* remote wakeup connected */
#define OHCI_CTRL_RWE (1 << 10) /* remote wakeup enable */
/* pre-shifted values for HCFS */
# define OHCI_USB_RESET (0 << 6)
# define OHCI_USB_RESUME (1 << 6)
# define OHCI_USB_OPER (2 << 6)
# define OHCI_USB_SUSPEND (3 << 6)
/*
* HcCommandStatus (cmdstatus) register masks
*/
#define OHCI_HCR (1 << 0) /* host controller reset */
#define OHCI_CLF (1 << 1) /* control list filled */
#define OHCI_BLF (1 << 2) /* bulk list filled */
#define OHCI_OCR (1 << 3) /* ownership change request */
#define OHCI_SOC (3 << 16) /* scheduling overrun count */
/*
* masks used with interrupt registers:
* HcInterruptStatus (intrstatus)
* HcInterruptEnable (intrenable)
* HcInterruptDisable (intrdisable)
*/
#define OHCI_INTR_SO (1 << 0) /* scheduling overrun */
#define OHCI_INTR_WDH (1 << 1) /* writeback of done_head */
#define OHCI_INTR_SF (1 << 2) /* start frame */
#define OHCI_INTR_RD (1 << 3) /* resume detect */
#define OHCI_INTR_UE (1 << 4) /* unrecoverable error */
#define OHCI_INTR_FNO (1 << 5) /* frame number overflow */
#define OHCI_INTR_RHSC (1 << 6) /* root hub status change */
#define OHCI_INTR_OC (1 << 30) /* ownership change */
#define OHCI_INTR_MIE (1 << 31) /* master interrupt enable */
/* OHCI ROOT HUB REGISTER MASKS */
/* roothub.portstatus [i] bits */
#define RH_PS_CCS 0x00000001 /* current connect status */
#define RH_PS_PES 0x00000002 /* port enable status*/
#define RH_PS_PSS 0x00000004 /* port suspend status */
#define RH_PS_POCI 0x00000008 /* port over current indicator */
#define RH_PS_PRS 0x00000010 /* port reset status */
#define RH_PS_PPS 0x00000100 /* port power status */
#define RH_PS_LSDA 0x00000200 /* low speed device attached */
#define RH_PS_CSC 0x00010000 /* connect status change */
#define RH_PS_PESC 0x00020000 /* port enable status change */
#define RH_PS_PSSC 0x00040000 /* port suspend status change */
#define RH_PS_OCIC 0x00080000 /* over current indicator change */
#define RH_PS_PRSC 0x00100000 /* port reset status change */
/* roothub.status bits */
#define RH_HS_LPS 0x00000001 /* local power status */
#define RH_HS_OCI 0x00000002 /* over current indicator */
#define RH_HS_DRWE 0x00008000 /* device remote wakeup enable */
#define RH_HS_LPSC 0x00010000 /* local power status change */
#define RH_HS_OCIC 0x00020000 /* over current indicator change */
#define RH_HS_CRWE 0x80000000 /* clear remote wakeup enable */
/* roothub.b masks */
#define RH_B_DR 0x0000ffff /* device removable flags */
#define RH_B_PPCM 0xffff0000 /* port power control mask */
/* roothub.a masks */
#define RH_A_NDP (0xff << 0) /* number of downstream ports */
#define RH_A_PSM (1 << 8) /* power switching mode */
#define RH_A_NPS (1 << 9) /* no power switching */
#define RH_A_DT (1 << 10) /* device type (mbz) */
#define RH_A_OCPM (1 << 11) /* over current protection mode */
#define RH_A_NOCP (1 << 12) /* no over current protection */
#define RH_A_POTPGT (0xff << 24) /* power on to power good time */
/* hcd-private per-urb state */
typedef struct urb_priv {
struct ed *ed;
__u16 length; // # tds in this request
__u16 td_cnt; // tds already serviced
struct td *td [0]; // all TDs in this request
} urb_priv_t;
#define TD_HASH_SIZE 64 /* power'o'two */
// sizeof (struct td) ~= 64 == 2^6 ...
#define TD_HASH_FUNC(td_dma) ((td_dma ^ (td_dma >> 6)) % TD_HASH_SIZE)
/*
* This is the full ohci controller description
*
* Note how the "proper" USB information is just
* a subset of what the full implementation needs. (Linus)
*/
struct ohci_hcd {
spinlock_t lock;
/*
* I/O memory used to communicate with the HC (dma-consistent)
*/
struct ohci_regs *regs;
/*
* main memory used to communicate with the HC (dma-consistent).
* hcd adds to schedule for a live hc any time, but removals finish
* only at the start of the next frame.
*/
struct ohci_hcca *hcca;
dma_addr_t hcca_dma;
struct ed *ed_rm_list; /* to be removed */
struct ed *ed_bulktail; /* last in bulk list */
struct ed *ed_controltail; /* last in ctrl list */
struct ed *periodic [NUM_INTS]; /* shadow int_table */
/*
* memory management for queue data structures
*/
struct pci_pool *td_cache;
struct pci_pool *ed_cache;
struct td *td_hash [TD_HASH_SIZE];
/*
* driver state
*/
int load [NUM_INTS];
u32 hc_control; /* copy of hc control reg */
unsigned long flags; /* for HC bugs */
#define OHCI_QUIRK_AMD756 0x01 /* erratum #4 */
#define OHCI_QUIRK_SUPERIO 0x02 /* natsemi */
// there are also chip quirks/bugs in init logic
/*
* framework state
*/
struct usb_hcd hcd;
};
#define hcd_to_ohci(hcd_ptr) container_of(hcd_ptr, struct ohci_hcd, hcd)
/*-------------------------------------------------------------------------*/
#ifndef DEBUG
#define STUB_DEBUG_FILES
#endif /* DEBUG */
#define ohci_dbg(ohci, fmt, args...) \
dev_dbg ((ohci)->hcd.controller , fmt , ## args )
#define ohci_err(ohci, fmt, args...) \
dev_err ((ohci)->hcd.controller , fmt , ## args )
#define ohci_info(ohci, fmt, args...) \
dev_info ((ohci)->hcd.controller , fmt , ## args )
#define ohci_warn(ohci, fmt, args...) \
dev_warn ((ohci)->hcd.controller , fmt , ## args )
#ifdef OHCI_VERBOSE_DEBUG
# define ohci_vdbg ohci_dbg
#else
# define ohci_vdbg(ohci, fmt, args...) do { } while (0)
#endif