Subversion Repositories shark

Rev

Go to most recent revision | Blame | Compare with Previous | Last modification | View Log | RSS feed

/* linux/drivers/i2c/scx200_i2c.c

   Copyright (c) 2001,2002 Christer Weinigel <wingel@nano-system.com>

   National Semiconductor SCx200 I2C bus on GPIO pins

   Based on i2c-velleman.c Copyright (C) 1995-96, 2000 Simon G. Vogl

   This program is free software; you can redistribute it and/or modify
   it under the terms of the GNU General Public License as published by
   the Free Software Foundation; either version 2 of the License, or
   (at your option) any later version.
   
   This program is distributed in the hope that it will be useful,
   but WITHOUT ANY WARRANTY; without even the implied warranty of
   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
   GNU General Public License for more details.
   
   You should have received a copy of the GNU General Public License
   along with this program; if not, write to the Free Software
   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.                 
*/


#include <linux/config.h>
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/i2c.h>
#include <linux/i2c-algo-bit.h>
#include <asm/io.h>

#include <linux/scx200_gpio.h>

#define NAME "scx200_i2c"

MODULE_AUTHOR("Christer Weinigel <wingel@nano-system.com>");
MODULE_DESCRIPTION("NatSemi SCx200 I2C Driver");
MODULE_LICENSE("GPL");

MODULE_PARM(scl, "i");
MODULE_PARM_DESC(scl, "GPIO line for SCL");
MODULE_PARM(sda, "i");
MODULE_PARM_DESC(sda, "GPIO line for SDA");

static int scl = CONFIG_SCx200_I2C_SCL;
static int sda = CONFIG_SCx200_I2C_SDA;

static void scx200_i2c_setscl(void *data, int state)
{
        scx200_gpio_set(scl, state);
}

static void scx200_i2c_setsda(void *data, int state)
{
        scx200_gpio_set(sda, state);
}

static int scx200_i2c_getscl(void *data)
{
        return scx200_gpio_get(scl);
}

static int scx200_i2c_getsda(void *data)
{
        return scx200_gpio_get(sda);
}

/* ------------------------------------------------------------------------
 * Encapsulate the above functions in the correct operations structure.
 * This is only done when more than one hardware adapter is supported.
 */


static struct i2c_algo_bit_data scx200_i2c_data = {
        NULL,
        scx200_i2c_setsda,
        scx200_i2c_setscl,
        scx200_i2c_getsda,
        scx200_i2c_getscl,
        10, 10, 100,            /* waits, timeout */
};

static struct i2c_adapter scx200_i2c_ops = {
        .owner             = THIS_MODULE,
        .algo_data         = &scx200_i2c_data,
        .name   = "NatSemi SCx200 I2C",
};

int scx200_i2c_init(void)
{
        printk(KERN_DEBUG NAME ": NatSemi SCx200 I2C Driver\n");

        if (!scx200_gpio_present()) {
                printk(KERN_ERR NAME ": no SCx200 gpio pins available\n");
                return -ENODEV;
        }

        printk(KERN_DEBUG NAME ": SCL=GPIO%02u, SDA=GPIO%02u\n",
               scl, sda);

        if (scl == -1 || sda == -1 || scl == sda) {
                printk(KERN_ERR NAME ": scl and sda must be specified\n");
                return -EINVAL;
        }

        /* Configure GPIOs as open collector outputs */
        scx200_gpio_configure(scl, ~2, 5);
        scx200_gpio_configure(sda, ~2, 5);

        if (i2c_bit_add_bus(&scx200_i2c_ops) < 0) {
                printk(KERN_ERR NAME ": adapter %s registration failed\n",
                       scx200_i2c_ops.name);
                return -ENODEV;
        }
       
        return 0;
}

void scx200_i2c_cleanup(void)
{
        i2c_bit_del_bus(&scx200_i2c_ops);
}

module_init(scx200_i2c_init);
module_exit(scx200_i2c_cleanup);

/*
    Local variables:
        compile-command: "make -k -C ../.. SUBDIRS=drivers/i2c modules"
        c-basic-offset: 8
    End:
*/