Subversion Repositories shark

Rev

Rev 422 | Blame | Compare with Previous | Last modification | View Log | RSS feed

#ifndef _LINUX_FDREG_H
#define _LINUX_FDREG_H
/*
 * This file contains some defines for the floppy disk controller.
 * Various sources. Mostly "IBM Microcomputers: A Programmers
 * Handbook", Sanches and Canton.
 */


#ifdef FDPATCHES
#define FD_IOPORT fdc_state[fdc].address
#else
/* It would be a lot saner just to force fdc_state[fdc].address to always
   be set ! FIXME */

#define FD_IOPORT 0x3f0
#endif

/* Fd controller regs. S&C, about page 340 */
#define FD_STATUS       (4 + FD_IOPORT )
#define FD_DATA         (5 + FD_IOPORT )

/* Digital Output Register */
#define FD_DOR          (2 + FD_IOPORT )

/* Digital Input Register (read) */
#define FD_DIR          (7 + FD_IOPORT )

/* Diskette Control Register (write)*/
#define FD_DCR          (7 + FD_IOPORT )

/* Bits of main status register */
#define STATUS_BUSYMASK 0x0F            /* drive busy mask */
#define STATUS_BUSY     0x10            /* FDC busy */
#define STATUS_DMA      0x20            /* 0- DMA mode */
#define STATUS_DIR      0x40            /* 0- cpu->fdc */
#define STATUS_READY    0x80            /* Data reg ready */

/* Bits of FD_ST0 */
#define ST0_DS          0x03            /* drive select mask */
#define ST0_HA          0x04            /* Head (Address) */
#define ST0_NR          0x08            /* Not Ready */
#define ST0_ECE         0x10            /* Equipment check error */
#define ST0_SE          0x20            /* Seek end */
#define ST0_INTR        0xC0            /* Interrupt code mask */

/* Bits of FD_ST1 */
#define ST1_MAM         0x01            /* Missing Address Mark */
#define ST1_WP          0x02            /* Write Protect */
#define ST1_ND          0x04            /* No Data - unreadable */
#define ST1_OR          0x10            /* OverRun */
#define ST1_CRC         0x20            /* CRC error in data or addr */
#define ST1_EOC         0x80            /* End Of Cylinder */

/* Bits of FD_ST2 */
#define ST2_MAM         0x01            /* Missing Address Mark (again) */
#define ST2_BC          0x02            /* Bad Cylinder */
#define ST2_SNS         0x04            /* Scan Not Satisfied */
#define ST2_SEH         0x08            /* Scan Equal Hit */
#define ST2_WC          0x10            /* Wrong Cylinder */
#define ST2_CRC         0x20            /* CRC error in data field */
#define ST2_CM          0x40            /* Control Mark = deleted */

/* Bits of FD_ST3 */
#define ST3_HA          0x04            /* Head (Address) */
#define ST3_DS          0x08            /* drive is double-sided */
#define ST3_TZ          0x10            /* Track Zero signal (1=track 0) */
#define ST3_RY          0x20            /* drive is ready */
#define ST3_WP          0x40            /* Write Protect */
#define ST3_FT          0x80            /* Drive Fault */

/* Values for FD_COMMAND */
#define FD_RECALIBRATE          0x07    /* move to track 0 */
#define FD_SEEK                 0x0F    /* seek track */
#define FD_READ                 0xE6    /* read with MT, MFM, SKip deleted */
#define FD_WRITE                0xC5    /* write with MT, MFM */
#define FD_SENSEI               0x08    /* Sense Interrupt Status */
#define FD_SPECIFY              0x03    /* specify HUT etc */
#define FD_FORMAT               0x4D    /* format one track */
#define FD_VERSION              0x10    /* get version code */
#define FD_CONFIGURE            0x13    /* configure FIFO operation */
#define FD_PERPENDICULAR        0x12    /* perpendicular r/w mode */
#define FD_GETSTATUS            0x04    /* read ST3 */
#define FD_DUMPREGS             0x0E    /* dump the contents of the fdc regs */
#define FD_READID               0xEA    /* prints the header of a sector */
#define FD_UNLOCK               0x14    /* Fifo config unlock */
#define FD_LOCK                 0x94    /* Fifo config lock */
#define FD_RSEEK_OUT            0x8f    /* seek out (i.e. to lower tracks) */
#define FD_RSEEK_IN             0xcf    /* seek in (i.e. to higher tracks) */

/* the following commands are new in the 82078. They are not used in the
 * floppy driver, except the first three. These commands may be useful for apps
 * which use the FDRAWCMD interface. For doc, get the 82078 spec sheets at
 * http://www-techdoc.intel.com/docs/periph/fd_contr/datasheets/ */


#define FD_PARTID               0x18    /* part id ("extended" version cmd) */
#define FD_SAVE                 0x2e    /* save fdc regs for later restore */
#define FD_DRIVESPEC            0x8e    /* drive specification: Access to the
                                         * 2 Mbps data transfer rate for tape
                                         * drives */

#define FD_RESTORE              0x4e    /* later restore */
#define FD_POWERDOWN            0x27    /* configure FDC's powersave features */
#define FD_FORMAT_N_WRITE       0xef    /* format and write in one go. */
#define FD_OPTION               0x33    /* ISO format (which is a clean way to
                                         * pack more sectors on a track) */

/* DMA commands */
#define DMA_READ        0x46
#define DMA_WRITE       0x4A

/* FDC version return types */
#define FDC_NONE        0x00
#define FDC_UNKNOWN     0x10    /* DO NOT USE THIS TYPE EXCEPT IF IDENTIFICATION
                                   FAILS EARLY */
#define FDC_8272A       0x20    /* Intel 8272a, NEC 765 */
#define FDC_765ED       0x30    /* Non-Intel 1MB-compatible FDC, can't detect */
#define FDC_82072       0x40    /* Intel 82072; 8272a + FIFO + DUMPREGS */
#define FDC_82072A      0x45    /* 82072A (on Sparcs) */
#define FDC_82077_ORIG  0x51    /* Original version of 82077AA, sans LOCK */
#define FDC_82077       0x52    /* 82077AA-1 */
#define FDC_82078_UNKN  0x5f    /* Unknown 82078 variant */
#define FDC_82078       0x60    /* 44pin 82078 or 64pin 82078SL */
#define FDC_82078_1     0x61    /* 82078-1 (2Mbps fdc) */
#define FDC_S82078B     0x62    /* S82078B (first seen on Adaptec AVA-2825 VLB
                                 * SCSI/EIDE/Floppy controller) */
#define FDC_87306       0x63    /* National Semiconductor PC 87306 */

/*
 * Beware: the fdc type list is roughly sorted by increasing features.
 * Presence of features is tested by comparing the FDC version id with the
 * "oldest" version that has the needed feature.
 * If during FDC detection, an obscure test fails late in the sequence, don't
 * assign FDC_UNKNOWN. Else the FDC will be treated as a dumb 8272a, or worse.
 * This is especially true if the tests are unneeded.
 */


#define FD_RESET_DELAY 20
#endif