Subversion Repositories shark

Rev

Go to most recent revision | Blame | Compare with Previous | Last modification | View Log | RSS feed

/*
 * drivers/i2c/i2c-ibm_iic.c
 *
 * Support for the IIC peripheral on IBM PPC 4xx
 *
 * Copyright (c) 2003 Zultys Technologies.
 * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
 *
 * Based on original work by
 *      Ian DaSilva  <idasilva@mvista.com>
 *      Armin Kuster <akuster@mvista.com>
 *      Matt Porter  <mporter@mvista.com>
 *
 *      Copyright 2000-2003 MontaVista Software Inc.
 *
 * Original driver version was highly leveraged from i2c-elektor.c
 *
 *      Copyright 1995-97 Simon G. Vogl
 *                1998-99 Hans Berglund
 *
 *      With some changes from Kyösti Mälkki <kmalkki@cc.hut.fi>
 *      and even Frodo Looijaard <frodol@dds.nl>
 *
 * This program is free software; you can redistribute  it and/or modify it
 * under  the terms of  the GNU General  Public License as published by the
 * Free Software Foundation;  either version 2 of the  License, or (at your
 * option) any later version.
 *
 */

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/ioport.h>
#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <linux/i2c.h>
#include <linux/i2c-id.h>
#include <asm/ocp.h>
#include <asm/ibm4xx.h>

#include "i2c-ibm_iic.h"

#define DRIVER_VERSION "2.0"

MODULE_DESCRIPTION("IBM IIC driver v" DRIVER_VERSION);
MODULE_LICENSE("GPL");

static int iic_scan = 0;
MODULE_PARM(iic_scan, "i");
MODULE_PARM_DESC(iic_scan, "Scan for active chips on the bus");

static int iic_force_poll = 0;
MODULE_PARM(iic_force_poll, "i");
MODULE_PARM_DESC(iic_force_poll, "Force polling mode");

static int iic_force_fast = 0;
MODULE_PARM(iic_force_fast, "i");
MODULE_PARM_DESC(iic_fast_poll, "Force fast mode (400 kHz)");

#define DBG_LEVEL 0

#ifdef DBG
#undef DBG
#endif

#ifdef DBG2
#undef DBG2
#endif

#if DBG_LEVEL > 0
#  define DBG(x...)     printk(KERN_DEBUG "ibm-iic" ##x)
#else
#  define DBG(x...)     ((void)0)
#endif
#if DBG_LEVEL > 1
#  define DBG2(x...)    DBG( ##x )
#else
#  define DBG2(x...)    ((void)0)
#endif
#if DBG_LEVEL > 2
static void dump_iic_regs(const char* header, struct ibm_iic_private* dev)
{
        volatile struct iic_regs *iic = dev->vaddr;
        printk(KERN_DEBUG "ibm-iic%d: %s\n", dev->idx, header);
        printk(KERN_DEBUG "  cntl     = 0x%02x, mdcntl = 0x%02x\n"
               KERN_DEBUG "  sts      = 0x%02x, extsts = 0x%02x\n"
               KERN_DEBUG "  clkdiv   = 0x%02x, xfrcnt = 0x%02x\n"
               KERN_DEBUG "  xtcntlss = 0x%02x, directcntl = 0x%02x\n",
                in_8(&iic->cntl), in_8(&iic->mdcntl), in_8(&iic->sts),
                in_8(&iic->extsts), in_8(&iic->clkdiv), in_8(&iic->xfrcnt),
                in_8(&iic->xtcntlss), in_8(&iic->directcntl));
}
#  define DUMP_REGS(h,dev)      dump_iic_regs((h),(dev))
#else
#  define DUMP_REGS(h,dev)      ((void)0)
#endif

/* Enable/disable interrupt generation */
static inline void iic_interrupt_mode(struct ibm_iic_private* dev, int enable)
{
        out_8(&dev->vaddr->intmsk, enable ? INTRMSK_EIMTC : 0);
}
 
/*
 * Initialize IIC interface.
 */

static void iic_dev_init(struct ibm_iic_private* dev)
{
        volatile struct iic_regs *iic = dev->vaddr;

        DBG("%d: init\n", dev->idx);
       
        /* Clear master address */
        out_8(&iic->lmadr, 0);
        out_8(&iic->hmadr, 0);

        /* Clear slave address */
        out_8(&iic->lsadr, 0);
        out_8(&iic->hsadr, 0);

        /* Clear status & extended status */
        out_8(&iic->sts, STS_SCMP | STS_IRQA);
        out_8(&iic->extsts, EXTSTS_IRQP | EXTSTS_IRQD | EXTSTS_LA
                            | EXTSTS_ICT | EXTSTS_XFRA);

        /* Set clock divider */
        out_8(&iic->clkdiv, dev->clckdiv);

        /* Clear transfer count */
        out_8(&iic->xfrcnt, 0);

        /* Clear extended control and status */
        out_8(&iic->xtcntlss, XTCNTLSS_SRC | XTCNTLSS_SRS | XTCNTLSS_SWC
                            | XTCNTLSS_SWS);

        /* Clear control register */
        out_8(&iic->cntl, 0);
       
        /* Enable interrupts if possible */
        iic_interrupt_mode(dev, dev->irq >= 0);

        /* Set mode control */
        out_8(&iic->mdcntl, MDCNTL_FMDB | MDCNTL_EINT | MDCNTL_EUBS
                            | (dev->fast_mode ? MDCNTL_FSM : 0));

        DUMP_REGS("iic_init", dev);
}

/*
 * Reset IIC interface
 */

static void iic_dev_reset(struct ibm_iic_private* dev)
{
        volatile struct iic_regs *iic = dev->vaddr;
        int i;
        u8 dc;
       
        DBG("%d: soft reset\n", dev->idx);
        DUMP_REGS("reset", dev);
       
        /* Place chip in the reset state */
        out_8(&iic->xtcntlss, XTCNTLSS_SRST);
       
        /* Check if bus is free */
        dc = in_8(&iic->directcntl);   
        if (!DIRCTNL_FREE(dc)){
                DBG("%d: trying to regain bus control\n", dev->idx);
       
                /* Try to set bus free state */
                out_8(&iic->directcntl, DIRCNTL_SDAC | DIRCNTL_SCC);   
       
                /* Wait until we regain bus control */
                for (i = 0; i < 100; ++i){
                        dc = in_8(&iic->directcntl);
                        if (DIRCTNL_FREE(dc))
                                break;
                       
                        /* Toggle SCL line */
                        dc ^= DIRCNTL_SCC;
                        out_8(&iic->directcntl, dc);
                        udelay(10);
                        dc ^= DIRCNTL_SCC;
                        out_8(&iic->directcntl, dc);
                       
                        /* be nice */
                        cond_resched();
                }
        }
       
        /* Remove reset */
        out_8(&iic->xtcntlss, 0);
       
        /* Reinitialize interface */
        iic_dev_init(dev);
}

/*
 * IIC interrupt handler
 */

static irqreturn_t iic_handler(int irq, void *dev_id, struct pt_regs *regs)
{
        struct ibm_iic_private* dev = (struct ibm_iic_private*)dev_id;
        volatile struct iic_regs* iic = dev->vaddr;
       
        DBG2("%d: irq handler, STS = 0x%02x, EXTSTS = 0x%02x\n",
             dev->idx, in_8(&iic->sts), in_8(&iic->extsts));
       
        /* Acknowledge IRQ and wakeup iic_wait_for_tc */
        out_8(&iic->sts, STS_IRQA | STS_SCMP);
        wake_up_interruptible(&dev->wq);
       
        return IRQ_HANDLED;
}

/*
 * Get master transfer result and clear errors if any.
 * Returns the number of actually transferred bytes or error (<0)
 */

static int iic_xfer_result(struct ibm_iic_private* dev)
{
        volatile struct iic_regs *iic = dev->vaddr;    
       
        if (unlikely(in_8(&iic->sts) & STS_ERR)){
                DBG("%d: xfer error, EXTSTS = 0x%02x\n", dev->idx,
                        in_8(&iic->extsts));
                               
                /* Clear errors and possible pending IRQs */
                out_8(&iic->extsts, EXTSTS_IRQP | EXTSTS_IRQD |
                        EXTSTS_LA | EXTSTS_ICT | EXTSTS_XFRA);
                       
                /* Flush master data buffer */
                out_8(&iic->mdcntl, in_8(&iic->mdcntl) | MDCNTL_FMDB);
               
                /* Is bus free?
                 * If error happened during combined xfer
                 * IIC interface is usually stuck in some strange
                 * state, the only way out - soft reset.
                 */

                if ((in_8(&iic->extsts) & EXTSTS_BCS_MASK) != EXTSTS_BCS_FREE){
                        DBG("%d: bus is stuck, resetting\n", dev->idx);
                        iic_dev_reset(dev);
                }
                return -EREMOTEIO;
        }
        else
                return in_8(&iic->xfrcnt) & XFRCNT_MTC_MASK;
}

/*
 * Try to abort active transfer.
 */

static void iic_abort_xfer(struct ibm_iic_private* dev)
{
        volatile struct iic_regs *iic = dev->vaddr;
        unsigned long x;
       
        DBG("%d: iic_abort_xfer\n", dev->idx);
       
        out_8(&iic->cntl, CNTL_HMT);
       
        /*
         * Wait for the abort command to complete.
         * It's not worth to be optimized, just poll (timeout >= 1 tick)
         */

        x = jiffies + 2;
        while ((in_8(&iic->extsts) & EXTSTS_BCS_MASK) != EXTSTS_BCS_FREE){
                if (time_after(jiffies, x)){
                        DBG("%d: abort timeout, resetting...\n", dev->idx);
                        iic_dev_reset(dev);
                        return;
                }
                schedule();
        }

        /* Just to clear errors */
        iic_xfer_result(dev);
}

/*
 * Wait for master transfer to complete.
 * It puts current process to sleep until we get interrupt or timeout expires.
 * Returns the number of transferred bytes or error (<0)
 */

static int iic_wait_for_tc(struct ibm_iic_private* dev){
       
        volatile struct iic_regs *iic = dev->vaddr;
        int ret = 0;
       
        if (dev->irq >= 0){
                /* Interrupt mode */
                wait_queue_t wait;
                init_waitqueue_entry(&wait, current);
               
                add_wait_queue(&dev->wq, &wait);
                set_current_state(TASK_INTERRUPTIBLE);
                if (in_8(&iic->sts) & STS_PT)
                        schedule_timeout(dev->adap.timeout * HZ);
                set_current_state(TASK_RUNNING);
                remove_wait_queue(&dev->wq, &wait);
               
                if (unlikely(signal_pending(current))){
                        DBG("%d: wait interrupted\n", dev->idx);
                        ret = -ERESTARTSYS;
                } else if (unlikely(in_8(&iic->sts) & STS_PT)){
                        DBG("%d: wait timeout\n", dev->idx);
                        ret = -ETIMEDOUT;
                }
        }
        else {
                /* Polling mode */
                unsigned long x = jiffies + dev->adap.timeout * HZ;
               
                while (in_8(&iic->sts) & STS_PT){
                        if (unlikely(time_after(jiffies, x))){
                                DBG("%d: poll timeout\n", dev->idx);
                                ret = -ETIMEDOUT;
                                break;
                        }
               
                        if (unlikely(signal_pending(current))){
                                DBG("%d: poll interrupted\n", dev->idx);
                                ret = -ERESTARTSYS;
                                break;
                        }
                        schedule();
                }      
        }
       
        if (unlikely(ret < 0))
                iic_abort_xfer(dev);
        else
                ret = iic_xfer_result(dev);
       
        DBG2("%d: iic_wait_for_tc -> %d\n", dev->idx, ret);
       
        return ret;
}

/*
 * Low level master transfer routine
 */

static int iic_xfer_bytes(struct ibm_iic_private* dev, struct i2c_msg* pm,
                          int combined_xfer)
{
        volatile struct iic_regs *iic = dev->vaddr;
        char* buf = pm->buf;
        int i, j, loops, ret = 0;
        int len = pm->len;

        u8 cntl = (in_8(&iic->cntl) & CNTL_AMD) | CNTL_PT;
        if (pm->flags & I2C_M_RD)
                cntl |= CNTL_RW;
       
        loops = (len + 3) / 4;
        for (i = 0; i < loops; ++i, len -= 4){
                int count = len > 4 ? 4 : len;
                u8 cmd = cntl | ((count - 1) << CNTL_TCT_SHIFT);
               
                if (!(cntl & CNTL_RW))
                        for (j = 0; j < count; ++j)
                                out_8((volatile u8*)&iic->mdbuf, *buf++);
               
                if (i < loops - 1)
                        cmd |= CNTL_CHT;
                else if (combined_xfer)
                        cmd |= CNTL_RPST;
               
                DBG2("%d: xfer_bytes, %d, CNTL = 0x%02x\n", dev->idx, count, cmd);
               
                /* Start transfer */
                out_8(&iic->cntl, cmd);
               
                /* Wait for completion */
                ret = iic_wait_for_tc(dev);

                if (unlikely(ret < 0))
                        break;
                else if (unlikely(ret != count)){
                        DBG("%d: xfer_bytes, requested %d, transfered %d\n",
                                dev->idx, count, ret);
                       
                        /* If it's not a last part of xfer, abort it */
                        if (combined_xfer || (i < loops - 1))
                                iic_abort_xfer(dev);
                               
                        ret = -EREMOTEIO;
                        break;                         
                }
               
                if (cntl & CNTL_RW)
                        for (j = 0; j < count; ++j)
                                *buf++ = in_8((volatile u8*)&iic->mdbuf);
        }
       
        return ret > 0 ? 0 : ret;
}

/*
 * Set target slave address for master transfer
 */

static inline void iic_address(struct ibm_iic_private* dev, struct i2c_msg* msg)
{
        volatile struct iic_regs *iic = dev->vaddr;
        u16 addr = msg->addr;
       
        DBG2("%d: iic_address, 0x%03x (%d-bit)\n", dev->idx,
                addr, msg->flags & I2C_M_TEN ? 10 : 7);
       
        if (msg->flags & I2C_M_TEN){
            out_8(&iic->cntl, CNTL_AMD);
            out_8(&iic->lmadr, addr);
            out_8(&iic->hmadr, 0xf0 | ((addr >> 7) & 0x06));
        }
        else {
            out_8(&iic->cntl, 0);
            out_8(&iic->lmadr, addr << 1);
        }
}

static inline int iic_invalid_address(const struct i2c_msg* p)
{
        return (p->addr > 0x3ff) || (!(p->flags & I2C_M_TEN) && (p->addr > 0x7f));
}

static inline int iic_address_neq(const struct i2c_msg* p1,
                                  const struct i2c_msg* p2)
{
        return (p1->addr != p2->addr)
                || ((p1->flags & I2C_M_TEN) != (p2->flags & I2C_M_TEN));
}

/*
 * Generic master transfer entrypoint.
 * Returns the number of processed messages or error (<0)
 */

static int iic_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
{
        struct ibm_iic_private* dev = (struct ibm_iic_private*)(i2c_get_adapdata(adap));
        volatile struct iic_regs *iic = dev->vaddr;
        int i, ret = 0;
       
        DBG2("%d: iic_xfer, %d msg(s)\n", dev->idx, num);
       
        if (!num)
                return 0;
       
        /* Check the sanity of the passed messages.
         * Uhh, generic i2c layer is more suitable place for such code...
         */

        if (unlikely(iic_invalid_address(&msgs[0]))){
                DBG("%d: invalid address 0x%03x (%d-bit)\n", dev->idx,
                        msgs[0].addr, msgs[0].flags & I2C_M_TEN ? 10 : 7);
                return -EINVAL;
        }              
        for (i = 0; i < num; ++i){
                if (unlikely(msgs[i].len <= 0)){
                        DBG("%d: invalid len %d in msg[%d]\n", dev->idx,
                                msgs[i].len, i);
                        return -EINVAL;
                }
                if (unlikely(iic_address_neq(&msgs[0], &msgs[i]))){
                        DBG("%d: invalid addr in msg[%d]\n", dev->idx, i);
                        return -EINVAL;
                }
        }
       
        /* Check bus state */
        if (unlikely((in_8(&iic->extsts) & EXTSTS_BCS_MASK) != EXTSTS_BCS_FREE)){
                DBG("%d: iic_xfer, bus is not free\n", dev->idx);
               
                /* Usually it means something serious has happend.
                 * We *cannot* have unfinished previous transfer
                 * so it doesn't make any sense to try to stop it.
                 * Probably we were not able to recover from the
                 * previous error.
                 * The only *reasonable* thing I can think of here
                 * is soft reset.  --ebs
                 */

                iic_dev_reset(dev);
               
                if ((in_8(&iic->extsts) & EXTSTS_BCS_MASK) != EXTSTS_BCS_FREE){
                        DBG("%d: iic_xfer, bus is still not free\n", dev->idx);
                        return -EREMOTEIO;
                }
        }
        else {
                /* Flush master data buffer (just in case) */
                out_8(&iic->mdcntl, in_8(&iic->mdcntl) | MDCNTL_FMDB);
        }
       
        /* Load slave address */
        iic_address(dev, &msgs[0]);
       
        /* Do real transfer */
        for (i = 0; i < num && !ret; ++i)
                ret = iic_xfer_bytes(dev, &msgs[i], i < num - 1);

        return ret < 0 ? ret : num;
}

static u32 iic_func(struct i2c_adapter *adap)
{
        return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_10BIT_ADDR;
}

static struct i2c_algorithm iic_algo = {
        .name           = "IBM IIC algorithm",
        .id             = I2C_ALGO_OCP,
        .master_xfer    = iic_xfer,
        .smbus_xfer     = NULL,
        .slave_send     = NULL,
        .slave_recv     = NULL,
        .algo_control   = NULL,
        .functionality  = iic_func
};

/*
 * Scan bus for valid 7-bit addresses (ie things that ACK on 1 byte read)
 * We only scan range [0x08 - 0x77], all other addresses are reserved anyway
 */

static void __devinit iic_scan_bus(struct ibm_iic_private* dev)
{
        int found = 0;
        char dummy;
        struct i2c_msg msg = {
                .buf   = &dummy,
                .len   = sizeof(dummy),
                .flags = I2C_M_RD
        };
       
        printk(KERN_INFO "ibm-iic%d: scanning bus...\n" KERN_INFO, dev->idx);
       
        for (msg.addr = 8; msg.addr < 0x78; ++msg.addr)
                if (iic_xfer(&dev->adap, &msg, 1) == 1){
                        ++found;
                        printk(" 0x%02x", msg.addr);
                }

        printk("%sibm-iic%d: %d device(s) detected\n",
                found ? "\n" KERN_INFO : "", dev->idx, found);
}

/*
 * Calculates IICx_CLCKDIV value for a specific OPB clock frequency
 */

static inline u8 iic_clckdiv(unsigned int opb)
{
        /* Compatibility kludge, should go away after all cards
         * are fixed to fill correct value for opbfreq.
         * Previous driver version used hardcoded divider value 4,
         * it corresponds to OPB frequency from the range (40, 50] MHz
         */

        if (!opb){
                printk(KERN_WARNING "ibm-iic: using compatibility value for OPB freq,"
                        " fix your board specific setup\n");
                opb = 50000000;
        }

        /* Convert to MHz */
        opb /= 1000000;
       
        if (opb < 20 || opb > 150){
                printk(KERN_CRIT "ibm-iic: invalid OPB clock frequency %u MHz\n",
                        opb);
                opb = opb < 20 ? 20 : 150;
        }
        return (u8)((opb + 9) / 10 - 1);
}

/*
 * Register single IIC interface
 */

static int __devinit iic_probe(struct ocp_device *ocp){

        struct ibm_iic_private* dev;
        struct i2c_adapter* adap;
        int ret;
        bd_t* bd = (bd_t*)&__res;
       
        if (!(dev = kmalloc(sizeof(*dev), GFP_KERNEL))){
                printk(KERN_CRIT "ibm-iic: failed to allocate device data\n");
                return -ENOMEM;
        }

        memset(dev, 0, sizeof(*dev));
        dev->idx = ocp->num;
        ocp_set_drvdata(ocp, dev);
       
        if (!(dev->vaddr = ioremap(ocp->paddr, sizeof(struct iic_regs)))){
                printk(KERN_CRIT "ibm-iic%d: failed to ioremap device registers\n",
                        dev->idx);
                ret = -ENXIO;
                goto fail2;
        }
       
        init_waitqueue_head(&dev->wq);

        dev->irq = iic_force_poll ? -1 : ocp->irq;
        if (dev->irq >= 0){
                /* Disable interrupts until we finish intialization,
                   assumes level-sensitive IRQ setup...
                 */

                iic_interrupt_mode(dev, 0);
                if (request_irq(dev->irq, iic_handler, 0, "IBM IIC", dev)){
                        printk(KERN_ERR "ibm-iic%d: request_irq %d failed\n",
                                dev->idx, dev->irq);
                        /* Fallback to the polling mode */     
                        dev->irq = -1;
                }
        }
       
        if (dev->irq < 0)
                printk(KERN_WARNING "ibm-iic%d: using polling mode\n",
                        dev->idx);
               
        /* Board specific settings */
        BUG_ON(dev->idx >= sizeof(bd->bi_iic_fast) / sizeof(bd->bi_iic_fast[0]));
        dev->fast_mode = iic_force_fast ? 1 : bd->bi_iic_fast[dev->idx];
       
        /* clckdiv is the same for *all* IIC interfaces,
         * but I'd rather make a copy than introduce another global. --ebs
         */

        dev->clckdiv = iic_clckdiv(bd->bi_opb_busfreq);
        DBG("%d: clckdiv = %d\n", dev->idx, dev->clckdiv);
       
        /* Initialize IIC interface */
        iic_dev_init(dev);
       
        /* Register it with i2c layer */
        adap = &dev->adap;
        strcpy(adap->dev.name, "IBM IIC");
        i2c_set_adapdata(adap, dev);
        adap->id = I2C_HW_OCP | iic_algo.id;
        adap->algo = &iic_algo;
        adap->client_register = NULL;
        adap->client_unregister = NULL;
        adap->timeout = 1;
        adap->retries = 1;

        if ((ret = i2c_add_adapter(adap)) != 0){
                printk(KERN_CRIT "ibm-iic%d: failed to register i2c adapter\n",
                        dev->idx);
                goto fail;
        }
       
        printk(KERN_INFO "ibm-iic%d: using %s mode\n", dev->idx,
                dev->fast_mode ? "fast (400 kHz)" : "standard (100 kHz)");

        /* Scan bus if requested by user */
        if (iic_scan)
                iic_scan_bus(dev);

        return 0;

fail:  
        if (dev->irq >= 0){
                iic_interrupt_mode(dev, 0);
                free_irq(dev->irq, dev);
        }      

        iounmap((void*)dev->vaddr);
fail2: 
        ocp_set_drvdata(ocp, 0);
        kfree(dev);    
        return ret;
}

/*
 * Cleanup initialized IIC interface
 */

static void __devexit iic_remove(struct ocp_device *ocp)
{
        struct ibm_iic_private* dev = (struct ibm_iic_private*)ocp_get_drvdata(ocp);
        BUG_ON(dev == NULL);
        if (i2c_del_adapter(&dev->adap)){
                printk(KERN_CRIT "ibm-iic%d: failed to delete i2c adapter :(\n",
                        dev->idx);
                /* That's *very* bad, just shutdown IRQ ... */
                if (dev->irq >= 0){
                    iic_interrupt_mode(dev, 0);
                    free_irq(dev->irq, dev);
                    dev->irq = -1;
                }
        } else {
                if (dev->irq >= 0){
                    iic_interrupt_mode(dev, 0);
                    free_irq(dev->irq, dev);
                }
                iounmap((void*)dev->vaddr);
                kfree(dev);
        }
}

static struct ocp_device_id ibm_iic_ids[] __devinitdata =
{
        { .vendor = OCP_VENDOR_IBM, .device = OCP_FUNC_IIC },
        { .vendor = OCP_VENDOR_INVALID }
};

MODULE_DEVICE_TABLE(ocp, ibm_iic_ids);

static struct ocp_driver ibm_iic_driver =
{
        .name           = "ocp_iic",
        .id_table       = ibm_iic_ids,
        .probe          = iic_probe,
        .remove         = __devexit_p(iic_remove),
#if defined(CONFIG_PM)
        .suspend        = NULL,
        .resume         = NULL,
#endif
};

static int __init iic_init(void)
{
        printk(KERN_INFO "IBM IIC driver v" DRIVER_VERSION "\n");
        return ocp_module_init(&ibm_iic_driver);
}

static void __exit iic_exit(void)
{
        ocp_unregister_driver(&ibm_iic_driver);
}

module_init(iic_init);
module_exit(iic_exit);