Subversion Repositories shark

Rev

Rev 422 | Blame | Compare with Previous | Last modification | View Log | RSS feed

/*
 * include/linux/serial_reg.h
 *
 * Copyright (C) 1992, 1994 by Theodore Ts'o.
 *
 * Redistribution of this file is permitted under the terms of the GNU
 * Public License (GPL)
 *
 * These are the UART port assignments, expressed as offsets from the base
 * register.  These assignments should hold for any serial port based on
 * a 8250, 16450, or 16550(A).
 */


#ifndef _LINUX_SERIAL_REG_H
#define _LINUX_SERIAL_REG_H

#define UART_RX         0       /* In:  Receive buffer (DLAB=0) */
#define UART_TX         0       /* Out: Transmit buffer (DLAB=0) */
#define UART_DLL        0       /* Out: Divisor Latch Low (DLAB=1) */
#define UART_TRG        0       /* (LCR=BF) FCTR bit 7 selects Rx or Tx
                                 * In: Fifo count
                                 * Out: Fifo custom trigger levels
                                 * XR16C85x only */

#define UART_DLM        1       /* Out: Divisor Latch High (DLAB=1) */
#define UART_IER        1       /* Out: Interrupt Enable Register */
#define UART_FCTR       1       /* (LCR=BF) Feature Control Register
                                 * XR16C85x only */

#define UART_IIR        2       /* In:  Interrupt ID Register */
#define UART_FCR        2       /* Out: FIFO Control Register */
#define UART_EFR        2       /* I/O: Extended Features Register */
                                /* (DLAB=1, 16C660 only) */

#define UART_LCR        3       /* Out: Line Control Register */
#define UART_MCR        4       /* Out: Modem Control Register */
#define UART_LSR        5       /* In:  Line Status Register */
#define UART_MSR        6       /* In:  Modem Status Register */
#define UART_SCR        7       /* I/O: Scratch Register */
#define UART_EMSR       7       /* (LCR=BF) Extended Mode Select Register
                                 * FCTR bit 6 selects SCR or EMSR
                                 * XR16c85x only */

/*
 * These are the definitions for the FIFO Control Register
 * (16650 only)
 */

#define UART_FCR_ENABLE_FIFO    0x01 /* Enable the FIFO */
#define UART_FCR_CLEAR_RCVR     0x02 /* Clear the RCVR FIFO */
#define UART_FCR_CLEAR_XMIT     0x04 /* Clear the XMIT FIFO */
#define UART_FCR_DMA_SELECT     0x08 /* For DMA applications */
#define UART_FCR_TRIGGER_MASK   0xC0 /* Mask for the FIFO trigger range */
#define UART_FCR_TRIGGER_1      0x00 /* Mask for trigger set at 1 */
#define UART_FCR_TRIGGER_4      0x40 /* Mask for trigger set at 4 */
#define UART_FCR_TRIGGER_8      0x80 /* Mask for trigger set at 8 */
#define UART_FCR_TRIGGER_14     0xC0 /* Mask for trigger set at 14 */
/* 16650 redefinitions */
#define UART_FCR6_R_TRIGGER_8   0x00 /* Mask for receive trigger set at 1 */
#define UART_FCR6_R_TRIGGER_16  0x40 /* Mask for receive trigger set at 4 */
#define UART_FCR6_R_TRIGGER_24  0x80 /* Mask for receive trigger set at 8 */
#define UART_FCR6_R_TRIGGER_28  0xC0 /* Mask for receive trigger set at 14 */
#define UART_FCR6_T_TRIGGER_16  0x00 /* Mask for transmit trigger set at 16 */
#define UART_FCR6_T_TRIGGER_8   0x10 /* Mask for transmit trigger set at 8 */
#define UART_FCR6_T_TRIGGER_24  0x20 /* Mask for transmit trigger set at 24 */
#define UART_FCR6_T_TRIGGER_30  0x30 /* Mask for transmit trigger set at 30 */
/* TI 16750 definitions */
#define UART_FCR7_64BYTE        0x20 /* Go into 64 byte mode */

/*
 * These are the definitions for the Line Control Register
 *
 * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
 * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
 */

#define UART_LCR_DLAB   0x80    /* Divisor latch access bit */
#define UART_LCR_SBC    0x40    /* Set break control */
#define UART_LCR_SPAR   0x20    /* Stick parity (?) */
#define UART_LCR_EPAR   0x10    /* Even parity select */
#define UART_LCR_PARITY 0x08    /* Parity Enable */
#define UART_LCR_STOP   0x04    /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
#define UART_LCR_WLEN5  0x00    /* Wordlength: 5 bits */
#define UART_LCR_WLEN6  0x01    /* Wordlength: 6 bits */
#define UART_LCR_WLEN7  0x02    /* Wordlength: 7 bits */
#define UART_LCR_WLEN8  0x03    /* Wordlength: 8 bits */

/*
 * These are the definitions for the Line Status Register
 */

#define UART_LSR_TEMT   0x40    /* Transmitter empty */
#define UART_LSR_THRE   0x20    /* Transmit-hold-register empty */
#define UART_LSR_BI     0x10    /* Break interrupt indicator */
#define UART_LSR_FE     0x08    /* Frame error indicator */
#define UART_LSR_PE     0x04    /* Parity error indicator */
#define UART_LSR_OE     0x02    /* Overrun error indicator */
#define UART_LSR_DR     0x01    /* Receiver data ready */

/*
 * These are the definitions for the Interrupt Identification Register
 */

#define UART_IIR_NO_INT 0x01    /* No interrupts pending */
#define UART_IIR_ID     0x06    /* Mask for the interrupt ID */

#define UART_IIR_MSI    0x00    /* Modem status interrupt */
#define UART_IIR_THRI   0x02    /* Transmitter holding register empty */
#define UART_IIR_RDI    0x04    /* Receiver data interrupt */
#define UART_IIR_RLSI   0x06    /* Receiver line status interrupt */

/*
 * These are the definitions for the Interrupt Enable Register
 */

#define UART_IER_MSI    0x08    /* Enable Modem status interrupt */
#define UART_IER_RLSI   0x04    /* Enable receiver line status interrupt */
#define UART_IER_THRI   0x02    /* Enable Transmitter holding register int. */
#define UART_IER_RDI    0x01    /* Enable receiver data interrupt */
/*
 * Sleep mode for ST16650 and TI16750.
 * Note that for 16650, EFR-bit 4 must be selected as well.
 */

#define UART_IERX_SLEEP  0x10   /* Enable sleep mode */

/*
 * These are the definitions for the Modem Control Register
 */

#define UART_MCR_LOOP   0x10    /* Enable loopback test mode */
#define UART_MCR_OUT2   0x08    /* Out2 complement */
#define UART_MCR_OUT1   0x04    /* Out1 complement */
#define UART_MCR_RTS    0x02    /* RTS complement */
#define UART_MCR_DTR    0x01    /* DTR complement */

/*
 * These are the definitions for the Modem Status Register
 */

#define UART_MSR_DCD    0x80    /* Data Carrier Detect */
#define UART_MSR_RI     0x40    /* Ring Indicator */
#define UART_MSR_DSR    0x20    /* Data Set Ready */
#define UART_MSR_CTS    0x10    /* Clear to Send */
#define UART_MSR_DDCD   0x08    /* Delta DCD */
#define UART_MSR_TERI   0x04    /* Trailing edge ring indicator */
#define UART_MSR_DDSR   0x02    /* Delta DSR */
#define UART_MSR_DCTS   0x01    /* Delta CTS */
#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */

/*
 * These are the definitions for the Extended Features Register
 * (StarTech 16C660 only, when DLAB=1)
 */

#define UART_EFR_CTS    0x80    /* CTS flow control */
#define UART_EFR_RTS    0x40    /* RTS flow control */
#define UART_EFR_SCD    0x20    /* Special character detect */
#define UART_EFR_ECB    0x10    /* Enhanced control bit */
/*
 * the low four bits control software flow control
 */


/*
 * These register definitions are for the 16C950
 */

#define UART_ASR        0x01    /* Additional Status Register */
#define UART_RFL        0x03    /* Receiver FIFO level */
#define UART_TFL        0x04    /* Transmitter FIFO level */
#define UART_ICR        0x05    /* Index Control Register */

/* The 16950 ICR registers */
#define UART_ACR        0x00    /* Additional Control Register */
#define UART_CPR        0x01    /* Clock Prescalar Register */
#define UART_TCR        0x02    /* Times Clock Register */
#define UART_CKS        0x03    /* Clock Select Register */
#define UART_TTL        0x04    /* Transmitter Interrupt Trigger Level */
#define UART_RTL        0x05    /* Receiver Interrupt Trigger Level */
#define UART_FCL        0x06    /* Flow Control Level Lower */
#define UART_FCH        0x07    /* Flow Control Level Higher */
#define UART_ID1        0x08    /* ID #1 */
#define UART_ID2        0x09    /* ID #2 */
#define UART_ID3        0x0A    /* ID #3 */
#define UART_REV        0x0B    /* Revision */
#define UART_CSR        0x0C    /* Channel Software Reset */
#define UART_NMR        0x0D    /* Nine-bit Mode Register */
#define UART_CTR        0xFF

/*
 * The 16C950 Additional Control Reigster
 */

#define UART_ACR_RXDIS  0x01    /* Receiver disable */
#define UART_ACR_TXDIS  0x02    /* Receiver disable */
#define UART_ACR_DSRFC  0x04    /* DSR Flow Control */
#define UART_ACR_TLENB  0x20    /* 950 trigger levels enable */
#define UART_ACR_ICRRD  0x40    /* ICR Read enable */
#define UART_ACR_ASREN  0x80    /* Additional status enable */

/*
 * These are the definitions for the Feature Control Register
 * (XR16C85x only, when LCR=bf; doubles with the Interrupt Enable
 * Register, UART register #1)
 */

#define UART_FCTR_RTS_NODELAY   0x00  /* RTS flow control delay */
#define UART_FCTR_RTS_4DELAY    0x01
#define UART_FCTR_RTS_6DELAY    0x02
#define UART_FCTR_RTS_8DELAY    0x03
#define UART_FCTR_IRDA  0x04  /* IrDa data encode select */
#define UART_FCTR_TX_INT        0x08  /* Tx interrupt type select */
#define UART_FCTR_TRGA  0x00  /* Tx/Rx 550 trigger table select */
#define UART_FCTR_TRGB  0x10  /* Tx/Rx 650 trigger table select */
#define UART_FCTR_TRGC  0x20  /* Tx/Rx 654 trigger table select */
#define UART_FCTR_TRGD  0x30  /* Tx/Rx 850 programmable trigger select */
#define UART_FCTR_SCR_SWAP      0x40  /* Scratch pad register swap */
#define UART_FCTR_RX    0x00  /* Programmable trigger mode select */
#define UART_FCTR_TX    0x80  /* Programmable trigger mode select */

/*
 * These are the definitions for the Enhanced Mode Select Register
 * (XR16C85x only, when LCR=bf and FCTR bit 6=1; doubles with the
 * Scratch register, UART register #7)
 */

#define UART_EMSR_FIFO_COUNT    0x01  /* Rx/Tx select */
#define UART_EMSR_ALT_COUNT     0x02  /* Alternating count select */

/*
 * These are the definitions for the Programmable Trigger
 * Register (XR16C85x only, when LCR=bf; doubles with the UART RX/TX
 * register, UART register #0)
 */

#define UART_TRG_1      0x01
#define UART_TRG_4      0x04
#define UART_TRG_8      0x08
#define UART_TRG_16     0x10
#define UART_TRG_32     0x20
#define UART_TRG_64     0x40
#define UART_TRG_96     0x60
#define UART_TRG_120    0x78
#define UART_TRG_128    0x80

/*
 * These definitions are for the RSA-DV II/S card, from
 *
 * Kiyokazu SUTO <suto@ks-and-ks.ne.jp>
 */


#define UART_RSA_BASE (-8)

#define UART_RSA_MSR ((UART_RSA_BASE) + 0) /* I/O: Mode Select Register */

#define UART_RSA_MSR_SWAP (1 << 0) /* Swap low/high 8 bytes in I/O port addr */
#define UART_RSA_MSR_FIFO (1 << 2) /* Enable the external FIFO */
#define UART_RSA_MSR_FLOW (1 << 3) /* Enable the auto RTS/CTS flow control */
#define UART_RSA_MSR_ITYP (1 << 4) /* Level (1) / Edge triger (0) */

#define UART_RSA_IER ((UART_RSA_BASE) + 1) /* I/O: Interrupt Enable Register */

#define UART_RSA_IER_Rx_FIFO_H (1 << 0) /* Enable Rx FIFO half full int. */
#define UART_RSA_IER_Tx_FIFO_H (1 << 1) /* Enable Tx FIFO half full int. */
#define UART_RSA_IER_Tx_FIFO_E (1 << 2) /* Enable Tx FIFO empty int. */
#define UART_RSA_IER_Rx_TOUT (1 << 3) /* Enable char receive timeout int */
#define UART_RSA_IER_TIMER (1 << 4) /* Enable timer interrupt */

#define UART_RSA_SRR ((UART_RSA_BASE) + 2) /* IN: Status Read Register */

#define UART_RSA_SRR_Tx_FIFO_NEMP (1 << 0) /* Tx FIFO is not empty (1) */
#define UART_RSA_SRR_Tx_FIFO_NHFL (1 << 1) /* Tx FIFO is not half full (1) */
#define UART_RSA_SRR_Tx_FIFO_NFUL (1 << 2) /* Tx FIFO is not full (1) */
#define UART_RSA_SRR_Rx_FIFO_NEMP (1 << 3) /* Rx FIFO is not empty (1) */
#define UART_RSA_SRR_Rx_FIFO_NHFL (1 << 4) /* Rx FIFO is not half full (1) */
#define UART_RSA_SRR_Rx_FIFO_NFUL (1 << 5) /* Rx FIFO is not full (1) */
#define UART_RSA_SRR_Rx_TOUT (1 << 6) /* Character reception timeout occurred (1) */
#define UART_RSA_SRR_TIMER (1 << 7) /* Timer interrupt occurred */

#define UART_RSA_FRR ((UART_RSA_BASE) + 2) /* OUT: FIFO Reset Register */

#define UART_RSA_TIVSR ((UART_RSA_BASE) + 3) /* I/O: Timer Interval Value Set Register */

#define UART_RSA_TCR ((UART_RSA_BASE) + 4) /* OUT: Timer Control Register */

#define UART_RSA_TCR_SWITCH (1 << 0) /* Timer on */

/*
 * The RSA DSV/II board has two fixed clock frequencies.  One is the
 * standard rate, and the other is 8 times faster.
 */

#define SERIAL_RSA_BAUD_BASE (921600)
#define SERIAL_RSA_BAUD_BASE_LO (SERIAL_RSA_BAUD_BASE / 8)

#endif /* _LINUX_SERIAL_REG_H */