Subversion Repositories shark

Rev

Rev 422 | Blame | Compare with Previous | Last modification | View Log | RSS feed

/* $Id: tpqic02.h,v 1.1 2004-01-28 15:26:51 giacomo Exp $
 *
 * Include file for QIC-02 driver for Linux.
 *
 * Copyright (c) 1992--1995 by H. H. Bergman. All rights reserved.
 *
 * ******* USER CONFIG SECTION BELOW (Near line 70) *******
 */


#ifndef _LINUX_TPQIC02_H
#define _LINUX_TPQIC02_H

#include <linux/config.h>

#if defined(CONFIG_QIC02_TAPE) || defined(CONFIG_QIC02_TAPE_MODULE)

/* need to have QIC02_TAPE_DRIVE and QIC02_TAPE_IFC expand to something */
#include <linux/mtio.h>


/* Make QIC02_TAPE_IFC expand to something.
 *
 * The only difference between WANGTEK and EVEREX is in the
 * handling of the DMA channel 3.
 * Note that the driver maps EVEREX to WANGTEK internally for speed
 * reasons. Externally WANGTEK==1, EVEREX==2, ARCHIVE==3.
 * These must correspond to the values used in qic02config(1).
 *
 * Support for Mountain controllers was added by Erik Jacobson
 * and severely hacked by me.   -- hhb
 *
 * Support for Emerald controllers by Alan Bain <afrb2@chiark.chu.cam.ac.uk>
 * with more hacks by me.   -- hhb
 */

#define WANGTEK         1                  /* don't know about Wangtek QIC-36 */
#define EVEREX          (WANGTEK+1)  /* I heard *some* of these are identical */
#define EVEREX_811V     EVEREX                        /* With TEAC MT 2ST 45D */
#define EVEREX_831V     EVEREX
#define ARCHIVE         3
#define ARCHIVE_SC400   ARCHIVE        /* rumoured to be from the pre-SMD-age */
#define ARCHIVE_SC402   ARCHIVE                /* don't know much about SC400 */
#define ARCHIVE_SC499   ARCHIVE       /* SC402 and SC499R should be identical */

#define MOUNTAIN        5                      /* Mountain Computer Interface */
#define EMERALD         6                      /* Emerald Interface card */



#define QIC02_TAPE_PORT_RANGE   8        /* number of IO locations to reserve */


/*********** START OF USER CONFIGURABLE SECTION ************/

/* Tape configuration: Select DRIVE, IFC, PORT, IRQ and DMA below.
 * Runtime (re)configuration is not supported yet.
 *
 * Tape drive configuration:    (MT_IS* constants are defined in mtio.h)
 *
 * QIC02_TAPE_DRIVE = MT_ISWT5150
 *      - Wangtek 5150, format: up to QIC-150.
 * QIC02_TAPE_DRIVE = MT_ISQIC02_ALL_FEATURES
 *      - Enables some optional QIC02 commands that some drives may lack.
 *        It is provided so you can check which are supported by your drive.
 *        Refer to tpqic02.h for others.
 *
 * Supported interface cards: QIC02_TAPE_IFC =
 *      WANGTEK,
 *      ARCHIVE_SC402, ARCHIVE_SC499.   (both same programming interface)
 *
 * Make sure you have the I/O ports/DMA channels
 * and IRQ stuff configured properly!
 * NOTE: There may be other device drivers using the same major
 *       number. This must be avoided. Check for timer.h conflicts too.
 *
 * If you have an EVEREX EV-831 card and you are using DMA channel 3,
 * you will probably have to ``#define QIC02_TAPE_DMA3_FIX'' below.
 */


/* CONFIG_QIC02_DYNCONF can be defined in autoconf.h, by `make config' */

/*** #undef CONFIG_QIC02_DYNCONF ***/

#ifndef CONFIG_QIC02_DYNCONF

#define QIC02_TAPE_DRIVE        MT_ISQIC02_ALL_FEATURES  /* drive type */
/* #define QIC02_TAPE_DRIVE     MT_ISWT5150 */
/* #define QIC02_TAPE_DRIVE     MT_ISARCHIVE_5945L2 */
/* #define QIC02_TAPE_DRIVE     MT_ISTEAC_MT2ST */
/* #define QIC02_TAPE_DRIVE     MT_ISARCHIVE_2150L */
/* #define QIC02_TAPE_DRIVE     MT_ISARCHIVESC499 */

/* Either WANGTEK, ARCHIVE or MOUNTAIN. Not EVEREX.
 * If you have an EVEREX, use WANGTEK and try the DMA3_FIX below.
 */

#define QIC02_TAPE_IFC          WANGTEK /* interface card type */
/* #define QIC02_TAPE_IFC               ARCHIVE */
/* #define QIC02_TAPE_IFC               MOUNTAIN */

#define QIC02_TAPE_PORT         0x300   /* controller port address */
#define QIC02_TAPE_IRQ          5       /* For IRQ2, use 9 here, others normal. */
#define QIC02_TAPE_DMA          1       /* either 1 or 3, because 2 is used by the floppy */

/* If DMA3 doesn't work, but DMA1 does, and you have a
 * Wangtek/Everex card, you can try #define-ing the flag
 * below. Note that you should also change the DACK jumper
 * for Wangtek/Everex cards when changing the DMA channel.
 */

#undef QIC02_TAPE_DMA3_FIX

/************ END OF USER CONFIGURABLE SECTION *************/

/* I put the stuff above in config.in, but a few recompiles, to
 * verify different configurations, and several days later I decided
 * to change it back again.
 */




/* NOTE: TP_HAVE_DENS should distinguish between available densities (?)
 * NOTE: Drive select is not implemented -- I have only one tape streamer,
 *       so I'm unable and unmotivated to test and implement that. ;-) ;-)
 */

#if QIC02_TAPE_DRIVE == MT_ISWT5150
#define TP_HAVE_DENS    1
#define TP_HAVE_BSF     0       /* nope */
#define TP_HAVE_FSR     0       /* nope */
#define TP_HAVE_BSR     0       /* nope */
#define TP_HAVE_EOD     0       /* most of the time */
#define TP_HAVE_SEEK    0
#define TP_HAVE_TELL    0
#define TP_HAVE_RAS1    1
#define TP_HAVE_RAS2    1

#elif QIC02_TAPE_DRIVE == MT_ISARCHIVESC499     /* Archive SC-499 QIC-36 controller */
#define TP_HAVE_DENS    1       /* can do set density (QIC-11 / QIC-24) */
#define TP_HAVE_BSF     0
#define TP_HAVE_FSR     1       /* can skip one block forwards */
#define TP_HAVE_BSR     1       /* can skip one block backwards */
#define TP_HAVE_EOD     1       /* can seek to end of recorded data */
#define TP_HAVE_SEEK    0
#define TP_HAVE_TELL    0
#define TP_HAVE_RAS1    1       /* can run selftest 1 */
#define TP_HAVE_RAS2    1       /* can run selftest 2 */
/* These last two selftests shouldn't be used yet! */

#elif (QIC02_TAPE_DRIVE == MT_ISARCHIVE_2060L) || (QIC02_TAPE_DRIVE == MT_ISARCHIVE_2150L)
#define TP_HAVE_DENS    1       /* can do set density (QIC-24 / QIC-120 / QIC-150) */
#define TP_HAVE_BSF     0
#define TP_HAVE_FSR     1       /* can skip one block forwards */
#define TP_HAVE_BSR     1       /* can skip one block backwards */
#define TP_HAVE_EOD     1       /* can seek to end of recorded data */
#define TP_HAVE_TELL    1       /* can read current block address */
#define TP_HAVE_SEEK    1       /* can seek to block */
#define TP_HAVE_RAS1    1       /* can run selftest 1 */
#define TP_HAVE_RAS2    1       /* can run selftest 2 */
/* These last two selftests shouldn't be used yet! */

#elif QIC02_TAPE_DRIVE == MT_ISARCHIVE_5945L2
/* can anyone verify this entry?? */
#define TP_HAVE_DENS    1       /* can do set density?? (QIC-24??) */
#define TP_HAVE_BSF     0
#define TP_HAVE_FSR     1       /* can skip one block forwards */
#define TP_HAVE_BSR     1       /* can skip one block backwards */
#define TP_HAVE_EOD     1       /* can seek to end of recorded data */
#define TP_HAVE_TELL    1       /* can read current block address */
#define TP_HAVE_SEEK    1       /* can seek to block */
#define TP_HAVE_RAS1    1       /* can run selftest 1 */
#define TP_HAVE_RAS2    1       /* can run selftest 2 */
/* These last two selftests shouldn't be used yet! */

#elif QIC02_TAPE_DRIVE == MT_ISTEAC_MT2ST
/* can anyone verify this entry?? */
#define TP_HAVE_DENS    0       /* cannot do set density?? (QIC-150?) */
#define TP_HAVE_BSF     0
#define TP_HAVE_FSR     1       /* can skip one block forwards */
#define TP_HAVE_BSR     1       /* can skip one block backwards */
#define TP_HAVE_EOD     1       /* can seek to end of recorded data */
#define TP_HAVE_SEEK    1       /* can seek to block */
#define TP_HAVE_TELL    1       /* can read current block address */
#define TP_HAVE_RAS1    1       /* can run selftest 1 */
#define TP_HAVE_RAS2    1       /* can run selftest 2 */
/* These last two selftests shouldn't be used yet! */

#elif QIC02_TAPE_DRIVE == MT_ISQIC02_ALL_FEATURES
#define TP_HAVE_DENS    1       /* can do set density */
#define TP_HAVE_BSF     1       /* can search filemark backwards */
#define TP_HAVE_FSR     1       /* can skip one block forwards */
#define TP_HAVE_BSR     1       /* can skip one block backwards */
#define TP_HAVE_EOD     1       /* can seek to end of recorded data */
#define TP_HAVE_SEEK    1       /* seek to block address */
#define TP_HAVE_TELL    1       /* tell current block address */
#define TP_HAVE_RAS1    1       /* can run selftest 1 */
#define TP_HAVE_RAS2    1       /* can run selftest 2 */
/* These last two selftests shouldn't be used yet! */


#else
#error No QIC-02 tape drive type defined!
/* If your drive is not listed above, first try the 'ALL_FEATURES',
 * to see what commands are supported, then create your own entry in
 * the list above. You may want to mail it to me, so that I can include
 * it in the next release.
 */

#endif

#endif /* !CONFIG_QIC02_DYNCONF */


/* WANGTEK interface card specifics */
#define WT_QIC02_STAT_PORT      (QIC02_TAPE_PORT)
#define WT_QIC02_CTL_PORT       (QIC02_TAPE_PORT)
#define WT_QIC02_CMD_PORT       (QIC02_TAPE_PORT+1)
#define WT_QIC02_DATA_PORT      (QIC02_TAPE_PORT+1)

/* status register bits (Active LOW!) */
#define WT_QIC02_STAT_POLARITY  0
#define WT_QIC02_STAT_READY     0x01
#define WT_QIC02_STAT_EXCEPTION 0x02
#define WT_QIC02_STAT_MASK      (WT_QIC02_STAT_READY|WT_QIC02_STAT_EXCEPTION)

#define WT_QIC02_STAT_RESETMASK 0x07
#define WT_QIC02_STAT_RESETVAL  (WT_QIC02_STAT_RESETMASK & ~WT_QIC02_STAT_EXCEPTION)

/* controller register (QIC02_CTL_PORT) bits */
#define WT_QIC02_CTL_RESET      0x02
#define WT_QIC02_CTL_REQUEST    0x04
#define WT_CTL_ONLINE           0x01
#define WT_CTL_CMDOFF           0xC0

#define WT_CTL_DMA3             0x10                      /* enable dma chan3 */
#define WT_CTL_DMA1             0x08             /* enable dma chan1 or chan2 */

/* EMERALD interface card specifics
 * Much like Wangtek, only different polarity and bit locations
 */

#define EMR_QIC02_STAT_PORT     (QIC02_TAPE_PORT)
#define EMR_QIC02_CTL_PORT      (QIC02_TAPE_PORT)
#define EMR_QIC02_CMD_PORT      (QIC02_TAPE_PORT+1)
#define EMR_QIC02_DATA_PORT     (QIC02_TAPE_PORT+1)

/* status register bits (Active High!) */
#define EMR_QIC02_STAT_POLARITY         1
#define EMR_QIC02_STAT_READY            0x01
#define EMR_QIC02_STAT_EXCEPTION        0x02
#define EMR_QIC02_STAT_MASK     (EMR_QIC02_STAT_READY|EMR_QIC02_STAT_EXCEPTION)

#define EMR_QIC02_STAT_RESETMASK        0x07
#define EMR_QIC02_STAT_RESETVAL (EMR_QIC02_STAT_RESETMASK & ~EMR_QIC02_STAT_EXCEPTION)

/* controller register (QIC02_CTL_PORT) bits */
#define EMR_QIC02_CTL_RESET     0x02
#define EMR_QIC02_CTL_REQUEST   0x04
#define EMR_CTL_ONLINE          0x01
#define EMR_CTL_CMDOFF          0xC0

#define EMR_CTL_DMA3            0x10                      /* enable dma chan3 */
#define EMR_CTL_DMA1            0x08             /* enable dma chan1 or chan2 */



/* ARCHIVE interface card specifics */
#define AR_QIC02_STAT_PORT      (QIC02_TAPE_PORT+1)
#define AR_QIC02_CTL_PORT       (QIC02_TAPE_PORT+1)
#define AR_QIC02_CMD_PORT       (QIC02_TAPE_PORT)
#define AR_QIC02_DATA_PORT      (QIC02_TAPE_PORT)

#define AR_START_DMA_PORT       (QIC02_TAPE_PORT+2)
#define AR_RESET_DMA_PORT       (QIC02_TAPE_PORT+3)

/* STAT port bits */
#define AR_QIC02_STAT_POLARITY  0
#define AR_STAT_IRQF            0x80    /* active high, interrupt request flag */
#define AR_QIC02_STAT_READY     0x40    /* active low */
#define AR_QIC02_STAT_EXCEPTION 0x20    /* active low */
#define AR_QIC02_STAT_MASK      (AR_QIC02_STAT_READY|AR_QIC02_STAT_EXCEPTION)
#define AR_STAT_DMADONE         0x10    /* active high, DMA done */
#define AR_STAT_DIRC            0x08    /* active high, direction */

#define AR_QIC02_STAT_RESETMASK 0x70    /* check RDY,EXC,DMADONE */
#define AR_QIC02_STAT_RESETVAL  ((AR_QIC02_STAT_RESETMASK & ~AR_STAT_IRQF & ~AR_QIC02_STAT_EXCEPTION) | AR_STAT_DMADONE)

/* CTL port bits */
#define AR_QIC02_CTL_RESET      0x80    /* drive reset */
#define AR_QIC02_CTL_REQUEST    0x40    /* notify of new command */
#define AR_CTL_IEN              0x20    /* interrupt enable */
#define AR_CTL_DNIEN            0x10    /* done-interrupt enable */
  /* Note: All of these bits are cleared automatically when writing to
   * AR_RESET_DMA_PORT. So AR_CTL_IEN and AR_CTL_DNIEN must be
   * reprogrammed before the write to AR_START_DMA_PORT.
   */



/* MOUNTAIN interface specifics */
#define MTN_QIC02_STAT_PORT     (QIC02_TAPE_PORT+1)
#define MTN_QIC02_CTL_PORT      (QIC02_TAPE_PORT+1)
#define MTN_QIC02_CMD_PORT      (QIC02_TAPE_PORT)
#define MTN_QIC02_DATA_PORT     (QIC02_TAPE_PORT)

#define MTN_W_SELECT_DMA_PORT   (QIC02_TAPE_PORT+2)
#define MTN_R_DESELECT_DMA_PORT (QIC02_TAPE_PORT+2)
#define MTN_W_DMA_WRITE_PORT    (QIC02_TAPE_PORT+3)

/* STAT port bits */
#define MTN_QIC02_STAT_POLARITY  0
#define MTN_QIC02_STAT_READY     0x02   /* active low */
#define MTN_QIC02_STAT_EXCEPTION 0x04   /* active low */
#define MTN_QIC02_STAT_MASK      (MTN_QIC02_STAT_READY|MTN_QIC02_STAT_EXCEPTION)
#define MTN_STAT_DMADONE         0x01   /* active high, DMA done */

#define MTN_QIC02_STAT_RESETMASK 0x07   /* check RDY,EXC,DMADONE */
#define MTN_QIC02_STAT_RESETVAL  ((MTN_QIC02_STAT_RESETMASK & ~MTN_QIC02_STAT_EXCEPTION) | MTN_STAT_DMADONE)

/* CTL port bits */
#define MTN_QIC02_CTL_RESET_NOT  0x80   /* drive reset, active low */
#define MTN_QIC02_CTL_RESET      0x80   /* Fodder #definition to keep gcc happy */

#define MTN_QIC02_CTL_ONLINE     0x40   /* Put drive on line  */
#define MTN_QIC02_CTL_REQUEST    0x20   /* notify of new command */
#define MTN_QIC02_CTL_IRQ_DRIVER 0x10   /* Enable IRQ tristate driver */
#define MTN_QIC02_CTL_DMA_DRIVER 0x08   /* Enable DMA tristate driver */
#define MTN_CTL_EXC_IEN          0x04   /* Exception interrupt enable */
#define MTN_CTL_RDY_IEN          0x02   /* Ready interrupt enable */
#define MTN_CTL_DNIEN            0x01   /* done-interrupt enable */

#define MTN_CTL_ONLINE          (MTN_QIC02_CTL_RESET_NOT | MTN_QIC02_CTL_IRQ_DRIVER | MTN_QIC02_CTL_DMA_DRIVER)


#ifndef CONFIG_QIC02_DYNCONF

# define QIC02_TAPE_DEBUG       (qic02_tape_debug)

# if QIC02_TAPE_IFC == WANGTEK 
#  define QIC02_STAT_POLARITY   WT_QIC02_STAT_POLARITY
#  define QIC02_STAT_PORT       WT_QIC02_STAT_PORT
#  define QIC02_CTL_PORT        WT_QIC02_CTL_PORT
#  define QIC02_CMD_PORT        WT_QIC02_CMD_PORT
#  define QIC02_DATA_PORT       WT_QIC02_DATA_PORT

#  define QIC02_STAT_READY      WT_QIC02_STAT_READY
#  define QIC02_STAT_EXCEPTION  WT_QIC02_STAT_EXCEPTION
#  define QIC02_STAT_MASK       WT_QIC02_STAT_MASK
#  define QIC02_STAT_RESETMASK  WT_QIC02_STAT_RESETMASK
#  define QIC02_STAT_RESETVAL   WT_QIC02_STAT_RESETVAL

#  define QIC02_CTL_RESET       WT_QIC02_CTL_RESET
#  define QIC02_CTL_REQUEST     WT_QIC02_CTL_REQUEST

#  if QIC02_TAPE_DMA == 3
#   ifdef QIC02_TAPE_DMA3_FIX
#    define WT_CTL_DMA          WT_CTL_DMA1
#   else
#    define WT_CTL_DMA          WT_CTL_DMA3
#   endif
#  elif QIC02_TAPE_DMA == 1
#    define WT_CTL_DMA          WT_CTL_DMA1
#  else
#   error Unsupported or incorrect DMA configuration.
#  endif

# elif QIC02_TAPE_IFC == EMERALD
#  define QIC02_STAT_POLARITY   EMR_QIC02_STAT_POLARITY
#  define QIC02_STAT_PORT       EMR_QIC02_STAT_PORT
#  define QIC02_CTL_PORT        EMR_QIC02_CTL_PORT
#  define QIC02_CMD_PORT        EMR_QIC02_CMD_PORT
#  define QIC02_DATA_PORT       EMR_QIC02_DATA_PORT

#  define QIC02_STAT_READY      EMR_QIC02_STAT_READY
#  define QIC02_STAT_EXCEPTION  EMR_QIC02_STAT_EXCEPTION
#  define QIC02_STAT_MASK       EMR_QIC02_STAT_MASK
#  define QIC02_STAT_RESETMASK  EMR_QIC02_STAT_RESETMASK
#  define QIC02_STAT_RESETVAL   EMR_QIC02_STAT_RESETVAL

#  define QIC02_CTL_RESET       EMR_QIC02_CTL_RESET
#  define QIC02_CTL_REQUEST     EMR_QIC02_CTL_REQUEST

#  if QIC02_TAPE_DMA == 3
#   ifdef QIC02_TAPE_DMA3_FIX
#    define EMR_CTL_DMA         EMR_CTL_DMA1
#   else
#    define EMR_CTL_DMA         EMR_CTL_DMA3
#   endif
#  elif QIC02_TAPE_DMA == 1
#    define EMR_CTL_DMA         EMR_CTL_DMA1
#  else
#   error Unsupported or incorrect DMA configuration.
#  endif

# elif QIC02_TAPE_IFC == ARCHIVE
#  define QIC02_STAT_POLARITY   AR_QIC02_STAT_POLARITY
#  define QIC02_STAT_PORT       AR_QIC02_STAT_PORT
#  define QIC02_CTL_PORT        AR_QIC02_CTL_PORT
#  define QIC02_CMD_PORT        AR_QIC02_CMD_PORT
#  define QIC02_DATA_PORT       AR_QIC02_DATA_PORT

#  define QIC02_STAT_READY      AR_QIC02_STAT_READY
#  define QIC02_STAT_EXCEPTION  AR_QIC02_STAT_EXCEPTION
#  define QIC02_STAT_MASK       AR_QIC02_STAT_MASK
#  define QIC02_STAT_RESETMASK  AR_QIC02_STAT_RESETMASK
#  define QIC02_STAT_RESETVAL   AR_QIC02_STAT_RESETVAL

#  define QIC02_CTL_RESET       AR_QIC02_CTL_RESET
#  define QIC02_CTL_REQUEST     AR_QIC02_CTL_REQUEST

#  if QIC02_TAPE_DMA > 3        /* channel 2 is used by the floppy driver */
#   error DMA channels other than 1 and 3 are not supported.
#  endif

# elif QIC02_TAPE_IFC == MOUNTAIN
#  define QIC02_STAT_POLARITY   MTN_QIC02_STAT_POLARITY
#  define QIC02_STAT_PORT       MTN_QIC02_STAT_PORT
#  define QIC02_CTL_PORT        MTN_QIC02_CTL_PORT
#  define QIC02_CMD_PORT        MTN_QIC02_CMD_PORT
#  define QIC02_DATA_PORT       MTN_QIC02_DATA_PORT

#  define QIC02_STAT_READY      MTN_QIC02_STAT_READY
#  define QIC02_STAT_EXCEPTION  MTN_QIC02_STAT_EXCEPTION
#  define QIC02_STAT_MASK       MTN_QIC02_STAT_MASK
#  define QIC02_STAT_RESETMASK  MTN_QIC02_STAT_RESETMASK
#  define QIC02_STAT_RESETVAL   MTN_QIC02_STAT_RESETVAL

#  define QIC02_CTL_RESET       MTN_QIC02_CTL_RESET
#  define QIC02_CTL_REQUEST     MTN_QIC02_CTL_REQUEST

#  if QIC02_TAPE_DMA > 3        /* channel 2 is used by the floppy driver */
#   error DMA channels other than 1 and 3 are not supported.
#  endif

# else
#  error No valid interface card specified!
# endif /* QIC02_TAPE_IFC */


  /* An ugly hack to make sure WT_CTL_DMA is defined even for the
   * static, non-Wangtek case. The alternative was even worse.
   */

# ifndef WT_CTL_DMA
#  define WT_CTL_DMA            WT_CTL_DMA1
# endif

/*******************/

#else /* !CONFIG_QIC02_DYNCONF */

/* Now the runtime config version, using variables instead of constants.
 *
 * qic02_tape_dynconf is R/O for the kernel, set from userspace.
 * qic02_tape_ccb is private to the driver, R/W.
 */


# define QIC02_TAPE_DRIVE       (qic02_tape_dynconf.mt_type)
# define QIC02_TAPE_IFC         (qic02_tape_ccb.ifc_type)
# define QIC02_TAPE_IRQ         (qic02_tape_dynconf.irqnr)
# define QIC02_TAPE_DMA         (qic02_tape_dynconf.dmanr)
# define QIC02_TAPE_PORT        (qic02_tape_dynconf.port)
# define WT_CTL_DMA             (qic02_tape_ccb.dma_enable_value)
# define QIC02_TAPE_DEBUG       (qic02_tape_dynconf.debug)

# define QIC02_STAT_PORT        (qic02_tape_ccb.port_stat)
# define QIC02_CTL_PORT         (qic02_tape_ccb.port_ctl)
# define QIC02_CMD_PORT         (qic02_tape_ccb.port_cmd)
# define QIC02_DATA_PORT        (qic02_tape_ccb.port_data)

# define QIC02_STAT_POLARITY    (qic02_tape_ccb.stat_polarity)
# define QIC02_STAT_READY       (qic02_tape_ccb.stat_ready)
# define QIC02_STAT_EXCEPTION   (qic02_tape_ccb.stat_exception)
# define QIC02_STAT_MASK        (qic02_tape_ccb.stat_mask)

# define QIC02_STAT_RESETMASK   (qic02_tape_ccb.stat_resetmask)
# define QIC02_STAT_RESETVAL    (qic02_tape_ccb.stat_resetval)

# define QIC02_CTL_RESET        (qic02_tape_ccb.ctl_reset)
# define QIC02_CTL_REQUEST      (qic02_tape_ccb.ctl_request)

# define TP_HAVE_DENS           (qic02_tape_dynconf.have_dens)
# define TP_HAVE_BSF            (qic02_tape_dynconf.have_bsf)
# define TP_HAVE_FSR            (qic02_tape_dynconf.have_fsr)
# define TP_HAVE_BSR            (qic02_tape_dynconf.have_bsr)
# define TP_HAVE_EOD            (qic02_tape_dynconf.have_eod)
# define TP_HAVE_SEEK           (qic02_tape_dynconf.have_seek)
# define TP_HAVE_TELL           (qic02_tape_dynconf.have_tell)
# define TP_HAVE_RAS1           (qic02_tape_dynconf.have_ras1)
# define TP_HAVE_RAS2           (qic02_tape_dynconf.have_ras2)

#endif /* CONFIG_QIC02_DYNCONF */


/* "Vendor Unique" codes */
/* Archive seek & tell stuff */
#define AR_QCMDV_TELL_BLK       0xAE    /* read current block address */
#define AR_QCMDV_SEEK_BLK       0xAD    /* seek to specific block */
#define AR_SEEK_BUF_SIZE        3       /* address is 3 bytes */



/*
 * Misc common stuff
 */


/* Standard QIC-02 commands -- rev F.  All QIC-02 drives must support these */
#define QCMD_SEL_1      0x01            /* select drive 1 */
#define QCMD_SEL_2      0x02            /* select drive 2 */
#define QCMD_SEL_3      0x04            /* select drive 3 */
#define QCMD_SEL_4      0x08            /* select drive 4 */
#define QCMD_REWIND     0x21            /* rewind tape */
#define QCMD_ERASE      0x22            /* erase tape */
#define QCMD_RETEN      0x24            /* retension tape */
#define QCMD_WRT_DATA   0x40            /* write data */
#define QCMD_WRT_FM     0x60            /* write file mark */
#define QCMD_RD_DATA    0x80            /* read data */
#define QCMD_RD_FM      0xA0            /* read file mark (forward direction) */
#define QCMD_RD_STAT    0xC0            /* read status */

/* Other (optional/vendor unique) commands */
 /* Density commands are only valid when TP_BOM is set! */
#define QCMD_DENS_11    0x26            /* QIC-11 */
#define QCMD_DENS_24    0x27            /* QIC-24: 9 track 60MB */
#define QCMD_DENS_120   0x28            /* QIC-120: 15 track 120MB */
#define QCMD_DENS_150   0x29            /* QIC-150: 18 track 150MB */
#define QCMD_DENS_300   0x2A            /* QIC-300/QIC-2100 */
#define QCMD_DENS_600   0x2B            /* QIC-600/QIC-2200 */
/* don't know about QIC-1000 and QIC-1350 */

#define QCMD_WRTNU_DATA 0x40            /* write data, no underruns, insert filler. */
#define QCMD_SPACE_FWD  0x81            /* skip next block */
#define QCMD_SPACE_BCK  0x89            /* move tape head one block back -- very useful! */
#define QCMD_RD_FM_BCK  0xA8            /* read filemark (backwards) */
#define QCMD_SEEK_EOD   0xA3            /* skip to EOD */
#define QCMD_RD_STAT_X1 0xC1            /* read extended status 1 */
#define QCMD_RD_STAT_X2 0xC4            /* read extended status 2 */
#define QCMD_RD_STAT_X3 0xE0            /* read extended status 3 */
#define QCMD_SELF_TST1  0xC2            /* run self test 1 (nondestructive) */
#define QCMD_SELF_TST2  0xCA            /* run self test 2 (destructive) */



/* Optional, QFA (Quick File Access) commands.
 * Not all drives support this, but those that do could use these commands
 * to implement semi-non-sequential access. `mt fsf` would benefit from this.
 * QFA divides the tape into 2 partitions, a data and a directory partition,
 * causing some incompatibility problems wrt std QIC-02 data exchange.
 * It would be useful to cache the directory info, but that might be tricky
 * to do in kernel-space. [Size constraints.]
 * Refer to the QIC-02 specs, appendix A for more information.
 * I have no idea how other *nix variants implement QFA.
 * I have no idea which drives support QFA and which don't.
 */

#define QFA_ENABLE      0x2D            /* enter QFA mode, give @ BOT only */
#define QFA_DATA        0x20            /* select data partition */
#define QFA_DIR         0x23            /* select directory partition */
#define QFA_RD_POS      0xCF            /* read position+status bytes */
#define QFA_SEEK_EOD    0xA1            /* seek EOD within current partition */
#define QFA_SEEK_BLK    0xAF            /* seek to a block within current partition */




/*
 * Debugging flags
 */

#define TPQD_SENSE_TEXT 0x0001
#define TPQD_SENSE_CNTS 0x0002
#define TPQD_REWIND     0x0004
#define TPQD_TERM_CYCLE 0x0008
#define TPQD_IOCTLS     0x0010
#define TPQD_DMAX       0x0020
#define TPQD_BLKSZ      0x0040
#define TPQD_MISC       0x0080

#define TPQD_DEBUG      0x0100

#define TPQD_DIAGS      0x1000

#define TPQD_ALWAYS     0x8000

#define TPQD_DEFAULT_FLAGS      0x00fc


#define TPQDBG(f)       ((QIC02_TAPE_DEBUG) & (TPQD_##f))


/* Minor device codes for tapes:
 * |7|6|5|4|3|2|1|0|
 *  | \ | / \ | / |_____ 1=rewind on close, 0=no rewind on close
 *  |  \|/    |_________ Density: 000=none, 001=QIC-11, 010=24, 011=120,
 *  |   |                100=QIC-150, 101..111 reserved.
 *  |   |_______________ Reserved for unit numbers.
 *  |___________________ Reserved for diagnostics during debugging.
 */


#define TP_REWCLOSE(d)  ((d)&1)                 /* rewind bit */
                           /* rewind is only done if data has been transferred */
#define TP_DENS(d)      (((d) >> 1) & 0x07)           /* tape density */
#define TP_UNIT(d)      (((d) >> 4) & 0x07)            /* unit number */

/* print excessive diagnostics */
#define TP_DIAGS(dev)   (QIC02_TAPE_DEBUG & TPQD_DIAGS)

/* status codes returned by a WTS_RDSTAT call */
struct tpstatus {       /* sizeof(short)==2), LSB first */
        unsigned short  exs;    /* Drive exception flags */
        unsigned short  dec;    /* data error count: nr of blocks rewritten/soft read errors */
        unsigned short  urc;    /* underrun count: nr of times streaming was interrupted */
};
#define TPSTATSIZE      sizeof(struct tpstatus)


/* defines for tpstatus.exs -- taken from 386BSD wt driver */
#define TP_POR          0x100   /* Power on or reset occurred */
#define TP_EOR          0x200   /* REServed for end of RECORDED media */
#define TP_PAR          0x400   /* REServed for bus parity */
#define TP_BOM          0x800   /* Beginning of media */
#define TP_MBD          0x1000  /* Marginal block detected */
#define TP_NDT          0x2000  /* No data detected */
#define TP_ILL          0x4000  /* Illegal command */
#define TP_ST1          0x8000  /* Status byte 1 flag */
#define TP_FIL          0x01    /* File mark detected */
#define TP_BNL          0x02    /* Bad block not located */
#define TP_UDA          0x04    /* Unrecoverable data error */
#define TP_EOM          0x08    /* End of media */
#define TP_WRP          0x10    /* Write protected cartridge */
#define TP_USL          0x20    /* Unselected drive */
#define TP_CNI          0x40    /* Cartridge not in place */
#define TP_ST0          0x80    /* Status byte 0 flag */

#define REPORT_ERR0     (TP_CNI|TP_USL|TP_WRP|TP_EOM|TP_UDA|TP_BNL|TP_FIL)
#define REPORT_ERR1     (TP_ILL|TP_NDT|TP_MBD|TP_PAR)


/* exception numbers */
#define EXC_UNKNOWN     0       /* (extra) Unknown exception code */
#define EXC_NDRV        1       /* No drive */
#define EXC_NCART       2       /* No cartridge */
#define EXC_WP          3       /* Write protected */
#define EXC_EOM         4       /* EOM */
#define EXC_RWA         5       /* read/write abort */
#define EXC_XBAD        6       /* read error, bad block transferred */
#define EXC_XFILLER     7       /* read error, filler block transferred */
#define EXC_NDT         8       /* read error, no data */
#define EXC_NDTEOM      9       /* read error, no data & EOM */
#define EXC_NDTBOM      10      /* read error, no data & BOM */
#define EXC_FM          11      /* Read a filemark */
#define EXC_ILL         12      /* Illegal command */
#define EXC_POR         13      /* Power on/reset */
#define EXC_MARGINAL    14      /* Marginal block detected */
#define EXC_EOR         15      /* (extra, for SEEKEOD) End Of Recorded data reached */
#define EXC_BOM         16      /* (extra) BOM reached */


#define TAPE_NOTIFY_TIMEOUT     1000000

/* internal function return codes */
#define TE_OK   0               /* everything is fine */
#define TE_EX   1               /* exception detected */
#define TE_ERR  2               /* some error */
#define TE_NS   3               /* can't read status */
#define TE_TIM  4               /* timed out */
#define TE_DEAD 5               /* tape drive doesn't respond */
#define TE_END  6               /******** Archive hack *****/

/* timeout timer values -- check these! */
#define TIM_S   (4*HZ)          /* 4 seconds (normal cmds) */
#define TIM_M   (30*HZ)         /* 30 seconds (write FM) */
#define TIM_R   (8*60*HZ)       /* 8 minutes (retensioning) */
#define TIM_F   (2*3600*HZ)     /* est. 1.2hr for full tape read/write+2 retens */

#define TIMERON(t)      mod_timer(&tp_timer, jiffies + (t))
#define TIMEROFF        del_timer_sync(&tp_timer);
#define TIMERCONT       add_timer(&tp_timer);


typedef char flag;
#define NO      0       /* NO must be 0 */
#define YES     1       /* YES must be != 0 */


#ifdef TDEBUG
# define TPQDEB(s)      s
# define TPQPUTS(s)     tpqputs(s)
#else
# define TPQDEB(s)
# define TPQPUTS(s)
#endif


/* NR_BLK_BUF is a `tuneable parameter'. If you're really low on
 * kernel space, you could decrease it to 1, or if you got a very
 * slow machine, you could increase it up to 127 blocks. Less kernel
 * buffer blocks result in more context-switching.
 */

#define NR_BLK_BUF      20                                  /* max 127 blocks */
#define TAPE_BLKSIZE    512               /* streamer tape block size (fixed) */
#define TPQBUF_SIZE     (TAPE_BLKSIZE*NR_BLK_BUF)              /* buffer size */


#define BLOCKS_BEYOND_EW        2       /* nr of blocks after Early Warning hole */
#define BOGUS_IRQ               32009


/* This is internal data, filled in based on the ifc_type field given
 * by the user. Everex is mapped to Wangtek with a different
 * `dma_enable_value', if dmanr==3.
 */

struct qic02_ccb {
        long    ifc_type;

        unsigned short  port_stat;      /* Status port address */
        unsigned short  port_ctl;       /* Control port address */
        unsigned short  port_cmd;       /* Command port address */
        unsigned short  port_data;      /* Data port address */

        /* status register bits */
        unsigned short  stat_polarity;  /* invert status bits or not */
        unsigned short  stat_ready;     /* drive ready */
        unsigned short  stat_exception; /* drive signals exception */
        unsigned short  stat_mask;
        unsigned short  stat_resetmask;
        unsigned short  stat_resetval;

        /* control register bits */
        unsigned short  ctl_reset;      /* reset drive */
        unsigned short  ctl_request;    /* latch command */
       
        /* This is used to change the DMA3 behaviour */
        unsigned short  dma_enable_value;
};

#if MODULE
static int qic02_tape_init(void);
#else
extern int qic02_tape_init(void);                         /* for mem.c */
#endif



#endif /* CONFIG_QIC02_TAPE */

#endif /* _LINUX_TPQIC02_H */