Subversion Repositories shark

Rev

Go to most recent revision | Blame | Compare with Previous | Last modification | View Log | RSS feed

#ifndef __LINUX_UHCI_HCD_H
#define __LINUX_UHCI_HCD_H

#include <linux/list.h>
#include <linux/usb.h>

#define usb_packetid(pipe)      (usb_pipein(pipe) ? USB_PID_IN : USB_PID_OUT)
#define PIPE_DEVEP_MASK         0x0007ff00

/*
 * Universal Host Controller Interface data structures and defines
 */


/* Command register */
#define USBCMD          0
#define   USBCMD_RS             0x0001  /* Run/Stop */
#define   USBCMD_HCRESET        0x0002  /* Host reset */
#define   USBCMD_GRESET         0x0004  /* Global reset */
#define   USBCMD_EGSM           0x0008  /* Global Suspend Mode */
#define   USBCMD_FGR            0x0010  /* Force Global Resume */
#define   USBCMD_SWDBG          0x0020  /* SW Debug mode */
#define   USBCMD_CF             0x0040  /* Config Flag (sw only) */
#define   USBCMD_MAXP           0x0080  /* Max Packet (0 = 32, 1 = 64) */

/* Status register */
#define USBSTS          2
#define   USBSTS_USBINT         0x0001  /* Interrupt due to IOC */
#define   USBSTS_ERROR          0x0002  /* Interrupt due to error */
#define   USBSTS_RD             0x0004  /* Resume Detect */
#define   USBSTS_HSE            0x0008  /* Host System Error - basically PCI problems */
#define   USBSTS_HCPE           0x0010  /* Host Controller Process Error - the scripts were buggy */
#define   USBSTS_HCH            0x0020  /* HC Halted */

/* Interrupt enable register */
#define USBINTR         4
#define   USBINTR_TIMEOUT       0x0001  /* Timeout/CRC error enable */
#define   USBINTR_RESUME        0x0002  /* Resume interrupt enable */
#define   USBINTR_IOC           0x0004  /* Interrupt On Complete enable */
#define   USBINTR_SP            0x0008  /* Short packet interrupt enable */

#define USBFRNUM        6
#define USBFLBASEADD    8
#define USBSOF          12

/* USB port status and control registers */
#define USBPORTSC1      16
#define USBPORTSC2      18
#define   USBPORTSC_CCS         0x0001  /* Current Connect Status ("device present") */
#define   USBPORTSC_CSC         0x0002  /* Connect Status Change */
#define   USBPORTSC_PE          0x0004  /* Port Enable */
#define   USBPORTSC_PEC         0x0008  /* Port Enable Change */
#define   USBPORTSC_LS          0x0030  /* Line Status */
#define   USBPORTSC_RD          0x0040  /* Resume Detect */
#define   USBPORTSC_LSDA        0x0100  /* Low Speed Device Attached */
#define   USBPORTSC_PR          0x0200  /* Port Reset */
#define   USBPORTSC_OC          0x0400  /* Over Current condition */
#define   USBPORTSC_SUSP        0x1000  /* Suspend */

/* Legacy support register */
#define USBLEGSUP               0xc0
#define   USBLEGSUP_DEFAULT     0x2000  /* only PIRQ enable set */

#define UHCI_NULL_DATA_SIZE     0x7FF   /* for UHCI controller TD */

#define UHCI_PTR_BITS           cpu_to_le32(0x000F)
#define UHCI_PTR_TERM           cpu_to_le32(0x0001)
#define UHCI_PTR_QH             cpu_to_le32(0x0002)
#define UHCI_PTR_DEPTH          cpu_to_le32(0x0004)
#define UHCI_PTR_BREADTH        cpu_to_le32(0x0000)

#define UHCI_NUMFRAMES          1024    /* in the frame list [array] */
#define UHCI_MAX_SOF_NUMBER     2047    /* in an SOF packet */
#define CAN_SCHEDULE_FRAMES     1000    /* how far future frames can be scheduled */

struct uhci_frame_list {
        __u32 frame[UHCI_NUMFRAMES];

        void *frame_cpu[UHCI_NUMFRAMES];

        dma_addr_t dma_handle;
};

struct urb_priv;

/*
 * One role of a QH is to hold a queue of TDs for some endpoint.  Each QH is
 * used with one URB, and qh->element (updated by the HC) is either:
 *   - the next unprocessed TD for the URB, or
 *   - UHCI_PTR_TERM (when there's no more traffic for this endpoint), or
 *   - the QH for the next URB queued to the same endpoint.
 *
 * The other role of a QH is to serve as a "skeleton" framelist entry, so we
 * can easily splice a QH for some endpoint into the schedule at the right
 * place.  Then qh->element is UHCI_PTR_TERM.
 *
 * In the frame list, qh->link maintains a list of QHs seen by the HC:
 *     skel1 --> ep1-qh --> ep2-qh --> ... --> skel2 --> ...
 */

struct uhci_qh {
        /* Hardware fields */
        __u32 link;                     /* Next queue */
        __u32 element;                  /* Queue element pointer */

        /* Software fields */
        dma_addr_t dma_handle;

        struct usb_device *dev;
        struct urb_priv *urbp;

        struct list_head list;          /* P: uhci->frame_list_lock */
        struct list_head remove_list;   /* P: uhci->remove_list_lock */
} __attribute__((aligned(16)));

/*
 * for TD <status>:
 */

#define td_status(td)           le32_to_cpu((td)->status)
#define TD_CTRL_SPD             (1 << 29)       /* Short Packet Detect */
#define TD_CTRL_C_ERR_MASK      (3 << 27)       /* Error Counter bits */
#define TD_CTRL_C_ERR_SHIFT     27
#define TD_CTRL_LS              (1 << 26)       /* Low Speed Device */
#define TD_CTRL_IOS             (1 << 25)       /* Isochronous Select */
#define TD_CTRL_IOC             (1 << 24)       /* Interrupt on Complete */
#define TD_CTRL_ACTIVE          (1 << 23)       /* TD Active */
#define TD_CTRL_STALLED         (1 << 22)       /* TD Stalled */
#define TD_CTRL_DBUFERR         (1 << 21)       /* Data Buffer Error */
#define TD_CTRL_BABBLE          (1 << 20)       /* Babble Detected */
#define TD_CTRL_NAK             (1 << 19)       /* NAK Received */
#define TD_CTRL_CRCTIMEO        (1 << 18)       /* CRC/Time Out Error */
#define TD_CTRL_BITSTUFF        (1 << 17)       /* Bit Stuff Error */
#define TD_CTRL_ACTLEN_MASK     0x7FF   /* actual length, encoded as n - 1 */

#define TD_CTRL_ANY_ERROR       (TD_CTRL_STALLED | TD_CTRL_DBUFERR | \
                                 TD_CTRL_BABBLE | TD_CTRL_CRCTIME | TD_CTRL_BITSTUFF)


#define uhci_maxerr(err)                ((err) << TD_CTRL_C_ERR_SHIFT)
#define uhci_status_bits(ctrl_sts)      ((ctrl_sts) & 0xFE0000)
#define uhci_actual_length(ctrl_sts)    (((ctrl_sts) + 1) & TD_CTRL_ACTLEN_MASK) /* 1-based */

/*
 * for TD <info>: (a.k.a. Token)
 */

#define td_token(td)            le32_to_cpu((td)->token)
#define TD_TOKEN_DEVADDR_SHIFT  8
#define TD_TOKEN_TOGGLE_SHIFT   19
#define TD_TOKEN_TOGGLE         (1 << 19)
#define TD_TOKEN_EXPLEN_SHIFT   21
#define TD_TOKEN_EXPLEN_MASK    0x7FF           /* expected length, encoded as n - 1 */
#define TD_TOKEN_PID_MASK       0xFF

#define uhci_explen(len)        ((len) << TD_TOKEN_EXPLEN_SHIFT)

#define uhci_expected_length(token) ((((token) >> 21) + 1) & TD_TOKEN_EXPLEN_MASK)
#define uhci_toggle(token)      (((token) >> TD_TOKEN_TOGGLE_SHIFT) & 1)
#define uhci_endpoint(token)    (((token) >> 15) & 0xf)
#define uhci_devaddr(token)     (((token) >> TD_TOKEN_DEVADDR_SHIFT) & 0x7f)
#define uhci_devep(token)       (((token) >> TD_TOKEN_DEVADDR_SHIFT) & 0x7ff)
#define uhci_packetid(token)    ((token) & TD_TOKEN_PID_MASK)
#define uhci_packetout(token)   (uhci_packetid(token) != USB_PID_IN)
#define uhci_packetin(token)    (uhci_packetid(token) == USB_PID_IN)

/*
 * The documentation says "4 words for hardware, 4 words for software".
 *
 * That's silly, the hardware doesn't care. The hardware only cares that
 * the hardware words are 16-byte aligned, and we can have any amount of
 * sw space after the TD entry as far as I can tell.
 *
 * But let's just go with the documentation, at least for 32-bit machines.
 * On 64-bit machines we probably want to take advantage of the fact that
 * hw doesn't really care about the size of the sw-only area.
 *
 * Alas, not anymore, we have more than 4 words for software, woops.
 * Everything still works tho, surprise! -jerdfelt
 *
 * td->link points to either another TD (not necessarily for the same urb or
 * even the same endpoint), or nothing (PTR_TERM), or a QH (for queued urbs)
 */

struct uhci_td {
        /* Hardware fields */
        __u32 link;
        __u32 status;
        __u32 token;
        __u32 buffer;

        /* Software fields */
        dma_addr_t dma_handle;

        struct usb_device *dev;
        struct urb *urb;

        struct list_head list;          /* P: urb->lock */
        struct list_head remove_list;   /* P: uhci->td_remove_list_lock */

        int frame;                      /* for iso: what frame? */
        struct list_head fl_list;       /* P: uhci->frame_list_lock */
} __attribute__((aligned(16)));

/*
 * The UHCI driver places Interrupt, Control and Bulk into QH's both
 * to group together TD's for one transfer, and also to faciliate queuing
 * of URB's. To make it easy to insert entries into the schedule, we have
 * a skeleton of QH's for each predefined Interrupt latency, low speed
 * control, high speed control and terminating QH (see explanation for
 * the terminating QH below).
 *
 * When we want to add a new QH, we add it to the end of the list for the
 * skeleton QH.
 *
 * For instance, the queue can look like this:
 *
 * skel int128 QH
 * dev 1 interrupt QH
 * dev 5 interrupt QH
 * skel int64 QH
 * skel int32 QH
 * ...
 * skel int1 QH
 * skel low speed control QH
 * dev 5 control QH
 * skel high speed control QH
 * skel bulk QH
 * dev 1 bulk QH
 * dev 2 bulk QH
 * skel terminating QH
 *
 * The terminating QH is used for 2 reasons:
 * - To place a terminating TD which is used to workaround a PIIX bug
 *   (see Intel errata for explanation)
 * - To loop back to the high speed control queue for full speed bandwidth
 *   reclamation
 *
 * Isochronous transfers are stored before the start of the skeleton
 * schedule and don't use QH's. While the UHCI spec doesn't forbid the
 * use of QH's for Isochronous, it doesn't use them either. Since we don't
 * need to use them either, we follow the spec diagrams in hope that it'll
 * be more compatible with future UHCI implementations.
 */


#define UHCI_NUM_SKELQH         12
#define skel_int128_qh          skelqh[0]
#define skel_int64_qh           skelqh[1]
#define skel_int32_qh           skelqh[2]
#define skel_int16_qh           skelqh[3]
#define skel_int8_qh            skelqh[4]
#define skel_int4_qh            skelqh[5]
#define skel_int2_qh            skelqh[6]
#define skel_int1_qh            skelqh[7]
#define skel_ls_control_qh      skelqh[8]
#define skel_hs_control_qh      skelqh[9]
#define skel_bulk_qh            skelqh[10]
#define skel_term_qh            skelqh[11]

/*
 * Search tree for determining where <interval> fits in the skelqh[]
 * skeleton.
 *
 * An interrupt request should be placed into the slowest skelqh[]
 * which meets the interval/period/frequency requirement.
 * An interrupt request is allowed to be faster than <interval> but not slower.
 *
 * For a given <interval>, this function returns the appropriate/matching
 * skelqh[] index value.
 */

static inline int __interval_to_skel(int interval)
{
        if (interval < 16) {
                if (interval < 4) {
                        if (interval < 2)
                                return 7;       /* int1 for 0-1 ms */
                        return 6;               /* int2 for 2-3 ms */
                }
                if (interval < 8)
                        return 5;               /* int4 for 4-7 ms */
                return 4;                       /* int8 for 8-15 ms */
        }
        if (interval < 64) {
                if (interval < 32)
                        return 3;               /* int16 for 16-31 ms */
                return 2;                       /* int32 for 32-63 ms */
        }
        if (interval < 128)
                return 1;                       /* int64 for 64-127 ms */
        return 0;                               /* int128 for 128-255 ms (Max.) */
}

/*
 * Device states for the host controller.
 *
 * To prevent "bouncing" in the presence of electrical noise,
 * we insist on a 1-second "grace" period, before switching to
 * the RUNNING or SUSPENDED states, during which the state is
 * not allowed to change.
 *
 * The resume process is divided into substates in order to avoid
 * potentially length delays during the timer handler.
 *
 * States in which the host controller is halted must have values <= 0.
 */

enum uhci_state {
        UHCI_RESET,
        UHCI_RUNNING_GRACE,             /* Before RUNNING */
        UHCI_RUNNING,                   /* The normal state */
        UHCI_SUSPENDING_GRACE,          /* Before SUSPENDED */
        UHCI_SUSPENDED = -10,           /* When no devices are attached */
        UHCI_RESUMING_1,
        UHCI_RESUMING_2
};

#define hcd_to_uhci(hcd_ptr) container_of(hcd_ptr, struct uhci_hcd, hcd)

/*
 * This describes the full uhci information.
 *
 * Note how the "proper" USB information is just
 * a subset of what the full implementation needs.
 */

struct uhci_hcd {
        struct usb_hcd hcd;

#ifdef CONFIG_PROC_FS
        /* procfs */
        struct proc_dir_entry *proc_entry;
#endif

        /* Grabbed from PCI */
        unsigned long io_addr;

        struct pci_pool *qh_pool;
        struct pci_pool *td_pool;

        struct usb_bus *bus;

        struct uhci_td *term_td;        /* Terminating TD, see UHCI bug */
        struct uhci_qh *skelqh[UHCI_NUM_SKELQH];        /* Skeleton QH's */

        spinlock_t frame_list_lock;
        struct uhci_frame_list *fl;             /* P: uhci->frame_list_lock */
        int fsbr;                               /* Full speed bandwidth reclamation */
        unsigned long fsbrtimeout;              /* FSBR delay */

        enum uhci_state state;                  /* FIXME: needs a spinlock */
        unsigned long state_end;                /* Time of next transition */
        int resume_detect;                      /* Need a Global Resume */

        /* Main list of URB's currently controlled by this HC */
        spinlock_t urb_list_lock;
        struct list_head urb_list;              /* P: uhci->urb_list_lock */

        /* List of QH's that are done, but waiting to be unlinked (race) */
        spinlock_t qh_remove_list_lock;
        struct list_head qh_remove_list;        /* P: uhci->qh_remove_list_lock */

        /* List of TD's that are done, but waiting to be freed (race) */
        spinlock_t td_remove_list_lock;
        struct list_head td_remove_list;        /* P: uhci->td_remove_list_lock */

        /* List of asynchronously unlinked URB's */
        spinlock_t urb_remove_list_lock;
        struct list_head urb_remove_list;       /* P: uhci->urb_remove_list_lock */

        /* List of URB's awaiting completion callback */
        spinlock_t complete_list_lock;
        struct list_head complete_list;         /* P: uhci->complete_list_lock */

        int rh_numports;

        struct timer_list stall_timer;
};

struct urb_priv {
        struct list_head urb_list;

        struct urb *urb;
        struct usb_device *dev;

        struct uhci_qh *qh;             /* QH for this URB */
        struct list_head td_list;       /* P: urb->lock */

        int fsbr : 1;                   /* URB turned on FSBR */
        int fsbr_timeout : 1;           /* URB timed out on FSBR */
        int queued : 1;                 /* QH was queued (not linked in) */
        int short_control_packet : 1;   /* If we get a short packet during */
                                        /*  a control transfer, retrigger */
                                        /*  the status phase */

        int status;                     /* Final status */

        unsigned long inserttime;       /* In jiffies */
        unsigned long fsbrtime;         /* In jiffies */

        struct list_head queue_list;    /* P: uhci->frame_list_lock */
        struct list_head complete_list; /* P: uhci->complete_list_lock */
};

/*
 * Locking in uhci.c
 *
 * spinlocks are used extensively to protect the many lists and data
 * structures we have. It's not that pretty, but it's necessary. We
 * need to be done with all of the locks (except complete_list_lock) when
 * we call urb->complete. I've tried to make it simple enough so I don't
 * have to spend hours racking my brain trying to figure out if the
 * locking is safe.
 *
 * Here's the safe locking order to prevent deadlocks:
 *
 * #1 uhci->urb_list_lock
 * #2 urb->lock
 * #3 uhci->urb_remove_list_lock, uhci->frame_list_lock,
 *   uhci->qh_remove_list_lock
 * #4 uhci->complete_list_lock
 *
 * If you're going to grab 2 or more locks at once, ALWAYS grab the lock
 * at the lowest level FIRST and NEVER grab locks at the same level at the
 * same time.
 *
 * So, if you need uhci->urb_list_lock, grab it before you grab urb->lock
 */


#endif